Questions and Answers for Everbilt 18 in. x 22 in. Sump Pump Basin

A:  Hi Richard. Yes, this basin can be used in this application although the 18 inch height may provide an issue. Please note that the basin cover, inlet hub/connector and pump must be purchased separately.

A:  This tub is much to large to fit under the sink. 

A:  Yes. Quite large though

A:  Hi Mildred. Our injection molded, high density polyethylene structural foam basin is the finest made.

A:  Yes, super sturdy but you will need to drill or cut any holes required.

A:  Water enters from top of basin or you can add holes by drilling.

A:  you have to drill them. some applications don't need them.

A:  On mine I came a little over half way up and drilled 1/2 holes about 3” apart  Also before I installed it I took a lot of dirt out around it and put rock back around it the basin Works perfect 

A:  Hello Drad. The installer has to cut/drill the inlet hole to suit their application and needs.

A:  I used mine for an outdoor sump pump. You can bury it or not depending on your situation. Works well either way

A:  Hello Apple. This basin does not need to be buried being used as a sump pump basin, but be sure to review local plumbing codes to ensure compliance.

A:  I buried mine in a pit of rocks, drilled holes in it so water could get in. When it fills up, a sump pumps the water out.

A:  It needs to be at an elevation that the water is coming in, normally on the floor, therefore it should be buried in the floor so the water runs into the can then pumped out

A:  Hello Teese52. Great question. The basin comes with 4-metal inserts secure the cover to the basin. The basin does not come with bolts but the two (2) Everbilt covers come with 4-bolts and washers. These are Store SKUs, 1000027540 and 1000027541. The bolts are 1/4 - 20 x 1 HHC-SS and the washers are 1/4" flat washers SS.

A:  The bolts and washers are included, they are small and maybe easy to misplace but they are stainless steel.

A:  They are steel of some sort, it doesn’t come with washers and bolts but they are cheap and easy to buy. I drilled a bunch of holes in it and used it for a yard sump pit.

A:  plastic lids, couple of different types, ie sump pump, grates only. Best I can remember hardware was included.

A:  The basin is well made of thick plastic. Mine has been installed in-ground for over 3 years and remains in excellent condition.

A:  No problem. My basin is in the backyard ground for more than 6 years

A:  No, it is designed to be installed in the ground. Obviously if you are moving heavy equipment over the basin it’ll crack. You would need one rated for the expected loading.

A:  The Basin is made out of plastic it will last quite a while for the intended purpose you have. However as with anything that is exposed to direct sunlight, this will reduce the life of the product. It will be a good Idea to put some kind of cover to protect from direct sunlight.

A:  HI Newb. The community answer is correct. You should have no issues with our sump basin in this application.

A:  My basin is in my basement where it has never been exposed to freezing temperatures. It is made of fairly hardy material so it should be able to tolerate temperature extremes. I'd say it's probably up to it. It's a shame you have to deal with your neighbors faulty drainage but good luck!

A:  HI Larry. There in no way to cut and rejoin this basin. Perhaps our 17 in. x 16 in. Sump Basin may work for you. It can be viewed at this link: https://www.homedepot.com/p/17-in-x-16-in-Sump-Basin-SF15/300454215. It is our model SF15 or SF-15DR which is perforated.

A:  Use galvanized deck plates bolted across the cut line, one inside and one outside. Two on each side and one on the bottom should hold it. You may want to use silicone caulk on the cut line but it is probably overkill. Cost will be minimal.

A:  I don't recommend you cut it at all, it will be almost impossible to get it back together with out any leaks. Try other options such as a smaller tub or enlarging the crawl space opening.

A:  Cut the basin where you need to cut it. Invert bottom portion you cut off, put bead od silicone around it insert in upper half and put few screws to hold them together under bottom of basin

A:  I didn’t run into that problem when I was installing mine. Maybe find some kind of glue that will stick to that I believe it may be a polyurethane type plastic. Maybe the same type that used for PVC pipe for the sprinkler systems the primer and the cement. And then use flex tape inside and out.

A:  I don't see that happening very easily but here's a thought: Usually, the only part of a sump pump tank that gets we is the lower half. You can also control that by adjusting the float. Perhaps it will make it easier if make your cut just slightly above the "wet line" since spicing it back would tend to be not as important if it did not have to be factory perfect. If none of that works then I would suggest you get in in there, bury it, back fill it and then reach down in the tub and apply and think epoxy coating to the inside.

A:  Thi s is not recommended for a 16-inch sump pump. Here is the link for the dimensions: https://images.homedepot-static.com/catalog/pdfImages/26/26e5592e-4f54-4da0-a31b-38eeec4fa5ee.pdf

A:  Hi BB. The diameter of this sump basin at the bottom is 16.338".

A:  Hi Bob. The diameter at the bottom is 16.338 inches

A:  18"

A:  About 18" diameter

A:  I also use it in my backyard for a sump but mine is buried with cement around the top of it. I cut out a heavier metal fence screen for the top with a 3/4" round wooden lid. The sump sides will probably take the weight, but what you use as the cover will be more of a concern for your riding mower. So I would make the lid over it something that will hold the weight and abuse of your mower... Hope this helps... Good luck...

A:  Well, I use it to catch water for a sumo pump well. with side dirt wall support. I do not know what weight limit it would have for a downward force. I would build a support over the basin so it would hold the weigh of me and my mower. .

A:  Hello PH. We offer no snarkey comments. What cover are you planning on using for this sump basin?

A:  This thing is heavy duty. I’ve placed it in my yard covering it with rocks. I don’t use a riding lawn mower but I wouldn’t think you would have an issue with the wheels passing over. To really answer your question you probably need to ask the manufacturer as I’m doubtful anyone here will be able to provide a weight limit for this item.