Q:Can you store this in an outdoor shed over the winter? I live in NY.
by|Oct 24, 2020
4 Answers
Answer This Question
A: I have not stored mine in a shed,but it has been in my garage not heated during the winter and it works just fine.i live in northeast ohio.hope that helps you.
by|Oct 26, 2020
A: Yes you can store it outside in a NY winter. Make sure you open up the valve on the bottom of the tank to drain any moisture and leave it open until again in use.
by|Oct 25, 2020
A: Yes just drain the water in the tank.
by|Oct 25, 2020
A: As long as you drain out any water that might be in the tank. Look for a valve on the bottom to see if it'll release condensation. If not, keep it inside. A new one that hasnt been used much should be okay in outside storage.
by|Oct 26, 2020
Q:Can I use clipped head nails
by|Aug 19, 2020
3 Answers
Answer This Question
A: NO.
by|Oct 6, 2020
A: No, because the clipped head nails are closer to each other than the full round head ones any therefore they will shoot two at a time, which can and will jam the gun.
But, one could use full round head nails in a clipped head nail gun as the nailer would simply drive one nail at a time.
by|Jan 4, 2021
A: Yes I do believe you can use clipped nail head nails, just make sure you get the proper angle for the gun.
by|Aug 20, 2020
Q:Does this draw a vacuum too
by|Aug 15, 2020
2 Answers
Answer This Question
A: No.
by|Oct 26, 2020
A: No. There is no fitting that goes over the intake to allow this. The intake is buried under a considerable amount of covering grid material.
by|Aug 16, 2020
Q:What is the difference in the FN250SB 16 ga. nailer in this kit and a FN250C 16 ga. nailer sold separately.
by|Aug 1, 2020
1 Answer
Answer This Question
A: Hello Ron, there is no difference between them. The FN250SB or FN250C. On comes in a kit and the other is a bare tool
by|Aug 3, 2020
Q:Does it shoot 16 Common nails ?
by|Jul 22, 2020
1 Answer
Answer This Question
A: FR350B requirements for nails are:
0.113"–0.148" (2.87–3.76 mm)diameter, plastic collated round head framing nails
Length: 2"–3-1/2" (50–90 mm)
Degree: 22º
by|Jul 23, 2020
Q:so this will shoot 16d nails? so I need to buy 21 degree 16d nails??
by|Jul 19, 2020
3 Answers
Answer This Question
A: Not sure on the 16d nails but make sure they're framing nails and yes they have to be 21 degree nails. The ones I bought are 2 3/8 in length and I also picked up 3" nails. Have fun.
by|Jul 21, 2020
A: 16d nails are 3½" so yes, this gun will shoot them. You will need to buy 21 degree nails because they come in strips which are set at the correct angle for the gun. Anything else would jam.
by|Jul 21, 2020
A: This Tool is excellent for the price . Reliable and user friendly. Light and easy to handle. I have mine almost two years and would buy again .
by|Jul 25, 2020
Q:Will the Porter Cable FR350B drive 3 1/4 inch galvanized ring shank nails?
by|Jul 17, 2020
3 Answers
Answer This Question
A: As long as they are 21 degree nails.
by|Oct 25, 2020
A: Yes it will drive the 3 1/4 inch galvanized rink shank nails. Also here are more specifications to your unit
FR350B Nails 0.113"–0.148" (2.87–3.76 mm) diameter
Plastic collated round head framing nails
Lengths 2"–3-1/2" (50–90 mm)
22º
by|Sep 25, 2020
2 found this answer helpful
A: Yes it can. I used 3 1/2” Nails just fine. It’s all about your regulator on your compressor. Just adjust your PSI to a higher range with longer nails and oil up when you’re done.
by|Oct 7, 2020
Q:Did anyone else notice the 18 and 16 guage have different model #s and have a different design? Seem cheaper quality
by|Jul 13, 2020
2 Answers
Answer This Question
A: PCFP12234 combo should come with models:
BN200SB uses standard 18 ga. brad nails from 5/8" to 2" long
FN250SB uses standard 16 ga. finish nails from 1" to 2-1/2" long
TS056: Heavy Duty 3/8" Crown stapler drives Heavy Duty 3/8"Crown Staples from1 /4" to 9/16" for multiple applications
by|Jul 13, 2020
A: Mine are the same design for the most part. They are no Bostich but get the job done for weekend warriors like me.
by|Jul 14, 2020
Q:Will there be a sale on this item on Independence Day
by|Jul 2, 2020
1 Answer
Answer This Question
A: Hi Lewis, unfortunately, we are not made aware of promotional codes and/or sales in advance. Stay in touch by registering for our online newsletter and receive special offers and promotions right in your inbox! Connect with us on Facebook, Twitter, and Pinterest for all kinds of inspiration!
Become a Home Depot insider:
http://pages.homedepot.com/Optin?storeId=10051&langId=-1&catalogId=10053&ExactTarget&email=&Source=GLOBALOPTIN
Facebook:
https://www.facebook.com/homedepot
Twitter:
https://twitter.com/HomeDepot
Pinterest:
http://pinterest.com/homedepot/
We appreciate your business and look forward to serving you in the future. Thank you for shopping Home Depot!
by|Aug 24, 2020
Q:Does it come with nails?
by|Jul 1, 2020
5 Answers
Answer This Question
A: There are 3 nail guns in the package, actually 2 nail-guns and a stapler. There is a small sample of each of the nails for each of the guns. Enough for a small project, but not enough to do more than get things moving.
by|Aug 16, 2020
A: No it does not. But it fully satisfies all that I have used it for.
by|Jul 3, 2020
A: No
by|Jul 4, 2020
A: It comes with a small number of nails
by|Jul 1, 2020
A: No, it doesn't come with nails. You'll need the correct gauge for each nailer.