Q:Does this make much of "click" sound when it turns on the lights. I have the Leviton brand currently and I find the click quite loud and am looking for a more quiet solution.
by|Mar 27, 2019
1 Answer
Answer This Question
A: Thank you for your inquiry. Please reach out to our Support Team at support@Lutron.com or by phone at 1 (844) 588-7661 for assistance with your inquiry.
by|Sep 21, 2019
Q:How long is the light on once activated by motion?
by|Mar 12, 2019
1 Answer
Answer This Question
A: The MS-VPS5M vacancy sensor switch has several timeout settings available. By default, it will keep the lights on until no motion has been detected for 5 minutes, and then the lights will turn off. You can find all of the possible timeout settings and programming methods on the install guide here: http://www.lutron.com/TechnicalDocumentLibrary/0301647.pdf.
by|Mar 14, 2019
Q:How can I keep the switch on without the sensor
by|Feb 18, 2019
1 Answer
Answer This Question
A: The MS-VPS5MH-WH cannot have its vacancy sensor bypassed to keep a lighting load on indefinitely. The maximum amount of time that the MS-VPS5MH-WH will keep a lighting load on for is 30 minutes. Please see the following programming guide for more information: http://www.lutron.com/TechnicalDocumentLibrary/048461.pdf
by|Feb 20, 2019
Q:I would like to use this in a bathroom because my light switch is behind the door. Is it possible to make the lights only (entry and vanity) on auto but keep the exhaust fan on manual? Or does everything have to be auto only? I don't want the exhaust fan to turn on automatically too because it seems unnecessary. I would want to manually turn that on when I needed it.
by|Dec 1, 2017
1 Answer
Answer This Question
A: The MS-OPS5M is rated for 5A of lighting load or 3A of mixed fan/lighting loads. All loads connected to it will act as the same circuit meaning they will turn on together and off together. Please see the following specification sheet for more information: http://www.lutron.com/TechnicalDocumentLibrary/369666.pdf
by|May 5, 2023
Q:can I also turn the lights off with my hand? No switch? Only sensor?
by|Mar 14, 2017
3 Answers
Answer This Question
A: Yes, the MS-OPS5M can turned on/off by the sensor or the manual tap-switch.
by|Sep 21, 2019
1 found this answer helpful
A: This can be used without a switch.
by|Sep 21, 2019
2 found this answer helpful
A: Either, that's what the button is on the top.
by|Mar 27, 2019
Q:The video indicates power comes on when motion is detected but the description doesn't confirm as much.
by|Jan 26, 2017
1 Answer
Answer This Question
A: This product is a vacancy only sensor and will not turn on when it senses motion. It will however turn off when it no longer senses motion in the room. The model number that would turn on with motion and off without motion would be the MS-OPS5M-BL.
by|May 4, 2023
Q:Can I connect 4 fixtures 128W (4 T8 32W each = 128W) each for a total of 512W to this Switch
by|Nov 8, 2016
2 Answers
Answer This Question
A: Hello Buzzard, I’m Chris from the Home Depot’s how-to Community. Thank you for your question.
The installation instructions specify “Up to 600 Watt incandescent, halogen, electronic low voltage; 200 Watt magnetic low voltage; 150 Watt CFL/ LED, 2-Amp magnetic and electronic ballasts, 3-Amp fan” as suitable.
Each of the fixtures you plan to install takes just over 1 amp each, so this switch could only handle one of them, not 4.
I hope this helps,
Chris.
.
by|Sep 21, 2019
2 found this answer helpful
A: Yes, this device is rated to control 5A of ballasted loads. Please visit the following page for specification information: http://www.lutron.com/TechnicalDocumentLibrary/0301647.pdf
by|May 5, 2023
Q:I have no ground in my switch boxes. I have used these just by themselves and wired the ground into the neutral and it works perfectly. Tried one of the 5 amp switches for a 3 way config and couldnt get it to work.
by|Dec 4, 2015
1 Answer
Answer This Question
A: Unfortunately Lutron cannot recommend tying in the ground connection into the neutral in any application. The dimming sensor, model MSCL-OP153M-WH, can be used without a ground connection, however you will want to ensure the load you are using is dimmable.