#1 Home Improvement Retailer

Cart

Cart

Home
Electrical
Wiring Devices & Light Controls
Timers

Questions and Answers for Lutron Maestro Countdown Timer Switch for Fans and Lights, 3A Fan/150W LED, Single-Pole/Multi-Location, Goldstone (MA-T51MN-GS)

Internet #204655146

Model #MA-T51MN-GS

Store SKU #1000516592

Maestro Countdown Timer Switch for Fans and Lights, 3A Fan/150W LED, Single-Pole/Multi-Location, Goldstone (MA-T51MN-GS)
(92)Questions & Answers (27)
  • Countdown timer switch for high efficiency exhaust fans/LED bulbs
  • Works with 3A high efficiency fans/150W LED bulbs
  • Reduce moisture and mildew in bathrooms; neutral wire required
View Full Product Details

Questions & Answers

27Questions
caret
Q:The switch doesn’t always turn on the fan, even though I have the timer set off?
by|Oct 5, 2019
1 Answer
Answer This Question

A:  The MA-T51 has a minimum load of 0.3A. If the fan it is controlling does not meet that minimum load, it may not turn the fan on consistently. Instead, if you have neutrals (bundle of white wires) located in the wallbox, Lutron would recommend using the MA-T51MN. This neutral-based timer has a minimum load of 0.05A.

by|Oct 8, 2019
    caret
    Q:Will this work with the "whisper quiet" bathroom exhaust fans that have a maximum load of 10.6W? The specifications normally give the maximum power supported, but this is a super-light load.
    by|Aug 13, 2019
    1 Answer
    Answer This Question

    A:  The MA-T51MN has a minimum load of .05A. The whisper quiet fan, with its 10.6W, operates at .088A, therefore the MA-T51MN should be able to control it. This particular timer does require a neutral connection, so ensure neutral wires are present in the wallbox where the MA-T51MN would be installed.

    by|Mar 20, 2023
      4 found this answer helpful
      caret
      Q:will this work with panisonic fans
      by|Jul 24, 2019
      4 Answers
      Answer This Question

      A:  The MA-T51 has a minimum load of 0.3A. Newer Panasonic fans typically have an operating load less than 0.3A. Lutron recommends using the MA-T51MN, which is a neutral-based timer. This drops the minimum load down to 0.05A.

      by|Jan 10, 2023
        2 found this answer helpful

        A:  Did not work in my case. I'll need to find an MA-T51MN version as advised by Lutron.

        by|Apr 13, 2023

          A:  Not in my case. The Panasonic fan didn't draw enough amperage for the switch to work.

          by|Jan 10, 2023
          1 found this answer helpful

          A:  I am sure it will ---Timer does not know to what device it is connected.

          by|Jan 10, 2023
          2 found this answer helpful
          caret
          Q:I already have a Lutron dimmer switch (color-white) installed. I want to put this countdown timer switch (color-snow) right next to it.
          by|Jul 18, 2019
          2 Answers
          Answer This Question

          A:  The snow finish will appear glossier than the white finish.

          by|Jan 6, 2023
            2 found this answer helpful

            A:  Actually, snow ("SW" suffix) is flat white; white ("WH" suffix) is gloss white. I am returning my snow timer because I want a gloss finish. Apparently, HD does not carry the WH version.

            by|Jul 29, 2023
              1 found this answer helpful
              caret
              Q:Can this be used for a bathroom heater on a dedicated 20 amp line?
              by|Jun 14, 2019
              1 Answer
              Answer This Question

              A:  The MA-T51MN is rated for 5A lighting. If the bathroom heater is a large incandescent/halogen bulb, make sure the wattage does not exceed 600W.

              by|Aug 26, 2023
                4 found this answer helpful
                caret
                Q:will this timer work for a fan without a light? I connected my new switch and the fan is stopping right after it starts and then after a few seconds the fans starts and stops again....
                by|Mar 5, 2019
                2 Answers
                Answer This Question

                A:  I have installed three of these---all on bathroom exhaust fans with no light---works perfectly.

                by|Mar 6, 2019

                A:  Yes, the MA-T51 could control a fan without a light. However, this timer has a minimum load of 0.3 amps or 36W. Based on the symptoms you are describing it sounds like your fan may not meet the minimum load of this control. Please reach out to our Support Team at support@Lutron.com or by phone at 1 (844) 588-7661 for further assistance with your inquiry.

                by|Mar 9, 2019
                  caret
                  Q:Can this be used on a dimmable LED light?
                  by|May 28, 2018
                  2 Answers
                  Answer This Question

                  A:  The MA-T51 is only rated to control 600W of incandescent/halogen, 450W of Magnetic Low Voltage halogen, a 3A fan ,or a 3A mixed lighting/fan load. Lutron would not suggest using LEDs with this device.

                  by|May 5, 2023

                    A:  No

                    by|May 5, 2023
                      caret
                      Q:Will this timer work with 120 volt to 24 volt step down transformer on a switched outlet?
                      by|Aug 23, 2017
                      1 Answer
                      Answer This Question

                      A:  Yes, this product is rated to be used on a step down transformer as long as the lighting load is incandescent or halogen.

                      by|Jul 29, 2023
                        1 found this answer helpful
                        caret
                        Q:Will this switch work with 24/12 volt applications?
                        by|Feb 21, 2017
                        1 Answer
                        Answer This Question

                        A:  This product is only rated to work in a 120v application and is not recommended for low voltage applications.

                        by|Jul 29, 2023
                          1 found this answer helpful
                          caret
                          Q:I need this neutral for it to work properly. Just replacing an existing one which is white in color.
                          by|Feb 11, 2017
                          1 Answer
                          Answer This Question

                          A:  Yes, this product does come with a neutral wire which is required for the device to function properly.

                          by|Jul 29, 2023
                            1 found this answer helpful
                            page 1 page 3