Questions and Answers for DEWALT 20V MAX XR Lithium-Ion Cordless Brushless 2-Speed 30° Paper Collated Framing Nailer (Tool Only)

A:  Buy it, . I have a house that took major damage down in the Bahamas. Used this tool the whole time I was down there with no issues. Had a small generator to run periodically to work the homes water pump and charge the batteries. Wouldn’t have been able to use air tools.

A:  We purchased this tool for our son because he was very specific about what he wanted. I just called him and relayed your question and he loves it for what he does, which is small projects and craft work. He said if you are in construction or using a nail gun regularly, he recommends air.

A:  I’ll never go back to air. I’ve roughed in a Basement with zero issues.

A:  I bought one and am a construction framer as a trade. Although this isn't my primary nailer as I use pneumatic ones, this unit is very dependable and allows me to nail areas not accessible and expedites the job. I have owned it for over a year with no problems at all and would buy it again.

A:  youre correct paslodes the std .. with this keep hammer at the ready not for any kind of production.. at all... hitachi if ya can find the brushless..

A:  The nail specifications for our DCN692 are: nail lengths: 2"-3 1/2"; (shank diameter: .113"-.131") 33-Degree.

A:  No, The nail specifications for this item are nail lengths: 2"-3 1/2"; (shank diameter: .113"-.131") 33-Degree.

A:  Dunno but it shoots 3.5 inch ring shank galvanized outdoor rated nails in pretty dang hard wood . The trick is using batteries under 5AH is a general no no..I use aftermarket 6.0 AH batts at 26 bux a pop

A:  yes but they jam up equally as much as all of the other nails we used!

A:  Yes, you can use galvanized nails for decks.

A:  Yes recommended.. I even use inside . Never know wer waters gonna be..

A:  The nails specifications for the DCN692 are 6 penny to 16 penny.

A:  Yes, the nails specifications for the DCN692 are 6 penny to 16 penny.

A:  The DCN692B will fire a nail every 1.5-2 seconds. The other information you requested is not currently available.

A:  The DCN692B will fire a nail every 1.5-2 seconds. We do not currently have specification on how may nails the DCN692B will fire on a single charge.

A:  This nailer accepts any 30° to 34° paper tape framing nail (clipped head or off set full round head) from 2 to 3.5 inches in length.

A:  Paslode nails don’t work to well in the dewalt framer. The hitachi nails work better. The framer does have problems shooting longer nails but overall it’s an awesome nailer

A:  best option sir..

A:  Paper tape, 30-34 degrees. I haven't been able to tell the difference between brands as long as the nails meet those two constraints.

A:  This DCN692 uses 30-34 degree nails

A:  I have used paslode 30 degree nails in this gun and they worked just fine. No jams, no problems.

A:  This gun requires 33 degree nails, Paslode 30 degree nails are not recommended. Mike

A:  Yes, Hitachi also

A:  This nailer kit weighs 1.4 lbs.

A:  The model number of the nailer is DCN692M1.

A:  Framing nailers do not define gauge. They are based on degrees. The DCN692 requires 30-34 degree, 2"-3 1/2" clipped head nails. Please contact DEWALT at 1-800-433-9258 for any other assistance.

A:  I dunno big it’s right on side of gun and it’s color coded too so the nails in Home Depot or supply house will match color on gun ... Wella..green I think it is use only passcode nails or dealt.. use nailer in bump mode only single jams excessively. It’s not warrantable either Dewalt knows about it. Real carpenters are never singling it anyway. Most fail in multiple mode not this un...