Questions and Answers for Stanley 32 in. H Plastic Folding Sawhorse (2 Pack)

A:  22 1/2”

A:  The top bar is just over 22 inches...approximately 221/4 inches.

A:  22&3/8 INCHES

A:  22.5 INCHES

A:  If your referring to the width of the top bar it's 22 3/8 of an inch.

A:  Get Some clamps They work well

A:  A pair of 2X4s fit firmly in the slots on top. You can then lay or attach your work table across the boards.

A:  You'd have to lay 2 x 4's in the slots, then have an appropriate clamp for your project.

A:  Don’t buy them, they are crap.

A:  I used giant c clamps

A:  When folded closed each sawhorse is 32”H X 22.5”W x 3”D

A:  32" tall x 22" wide x 2" deep

A:  Sorry cant tell you that due to its holding up a table top. If you call home depo they should be able to tell you.

A:  About 2 inches

A:  Each one just a little over 2 inches

A:  Barely. The horses are so narrow that a 4x8 sheet is unstable.

A:  They will. I offset the sawhorses some so the plywood can balance better.

A:  It can, but has a lot of side overhang.

A:  No problem using these saw horses to support a 4'x8' sheet of plywood, any thickness. I have had a lot more weight on mine. If you intend putting the plywood on it to measure and cut, no issues. If you plan on using it as a table or platform remember to center the weight. For additional support consider placing 2"x2" boards in the slots and attach the plywood to it. I made a "table" using a 3/4" piece of plywood 36"x52" supported by 2 2"x2" boards under it and use it as a portable workbench for different job sites.

A:  Yes. I am using them to support two 4x8 work benches.

A:  This sawhorse is 31 inches tall and 22 inches wide if that helps and if you ordered the 2 pak is a great deal.

A:  These sawhorses are 22" wide and 31" tall when they are opened up and 32" tall when they are folded closed.

A:  22 wide, 31 tall when set up

A:  The bottom base is 22 inches (each side of the "horse" laterally) and the unit is 31 inches tall.

A:  I do not understand what your question is. However I have these and they are great for home projects. They are sturdy and light weight. You can add two 2"x4" x8 ft pieces and you can then hold easily a 4'x8' panel of board. I used the to cut plywood for a project I was doing, worked great and easily stored after.

A:  Made in Isreal.

A:  Yes they are!

A:  The sticker on it says made in USS

A:  Our 32 in. Folding Sawhorse is manufactured in Israel.

A:  Yes, they are made in the USA.

A:  Let's see if its working

A:  14.5 inch

A:  13" closest to 16" widest

A:  The notches are from 13-16 inches (inner to outer measurement).

A:  13 inches apart.

A:  My daughter "stole" my set, but based on the top I made for them 24"

A:  22 Inch top bar

A:  The dimensions for the STST60952 are 22.5 x 5 x 31.9 inches.

A:  27"

A:  22" wide and 31" tall when open and 32" tall when (folded) closed

A:  22”

A:  Height

A:  31" in height when fully opened. and 32" in height when (folded) closed for storage..

A:  Height

A:  31” tall and 22” wide

A:  height

A:  Made of plastic; yes, it, does fold flat; lightweight.

A:  Plastic compound....Collapsible Very light....

A:  heavy plastic. it does collapse and probably weighs no more than 3 lbs each

A:  Plastic,collapsible and very light

A:  They are made of high quality plastic (or a compound similar) and I guess they weigh under 10 pounds. The are collapsible and when placed side by side are about 6 or 7 inches wide.