Q:What is the bus rating of this load center? thanks!
by|Jul 23, 2019
1 Answer
Answer This Question
A: For PW2040B1200CU the bus rating is 100% of the panel rating so 200A amps.
by|Jul 23, 2019
Q:Will this panel accept. Type QE breakers. Two pole 30 amp gfci seimans breakers.
by|Jul 14, 2019
3 Answers
Answer This Question
A: Can tandem single slot breakers be used in this box?
by|Jun 27, 2020
A: Yes it takes QE. Factory spec: Single phase factory installed 22kA IR main circuit breaker offers 22/10kA IR series combination rating when using 10kA type QP, QT, QPF, QE, QN, and QAF2/QAF2C
branch breakers. From Home Depot spec: Accepts Siemens type QP, QPH and HQP plug in circuit breakers.
by|Apr 3, 2020
A: Yes, Type QE breakers are listed for PW4040B1200CU as listed on the wiring diagram. Please refer to below link.
https://s3.amazonaws.com/dcc-data-extract/new-delta/asset/Compas/daily/Compas/2019-03-30/Wiring%20Diagram/SIE_WD_PW4040B1200CU_PW4040L1200CU.pdf
by|Jul 16, 2019
Q:Is this flush mount?
by|Feb 22, 2019
2 Answers
Answer This Question
A: No
by|May 31, 2021
1 found this answer helpful
A: The PW2020B1100CU is Surface mounted
by|Jan 24, 2021
Q:What type of main breaker does this come with?
by|Nov 4, 2018
4 Answers
Answer This Question
A: The main breaker is 2 pole 200 amp 240 volt.
by|Nov 10, 2018
A: PW2040B1200CU comes with EQ8695 factory installed which is available as replacement by ordering MBK200A. To download the cut sheet and wiring diagram for this item go to link below and click on "Downloads" and enter PW2040B1200CU in the search box.
https://w3.usa.siemens.com/powerdistribution/us/en/Pages/low-medium-voltage.aspx
by|Nov 5, 2018
A: Not sure I understand the question; however, you can find detail information about this load center at the Siemens web site below
https://w3.usa.siemens.com/powerdistribution/us/en/speedfax-product-catalog/Documents/2017/SF-17-Sect-01-ALL-web.pdf
by|Nov 5, 2018
A: 200 Amp Siemens
by|Nov 5, 2018
Q:I'm having trouble figuring out how the door latches. I removed it during the install, but when ...
by|Oct 15, 2018
2 Answers
Answer This Question
A: The pins (pintles) point up. The holes (gudgeons) of the door slide down on the pins while the door is open wide. A set screw is screwed in a pre-drilled hole above the bottom pin so the door can slide up and out when opened. The padlock latch inside the lower right is swung out and down. The door is closed. The will be a gap at the top, at first. You then push in lightly on the top of the door with one hand and push up at the bottom of the door with the other hand. The top of the door then slides up underneath the upper ridge lip. Push to door closed the rest of the way and the padlock while slide into the slot and lock the door.
by|Apr 3, 2020
A: There is no instruction sheet for the latch or cover installation. Please contact Technical Support at 1-800-333-7421 for assistance with your issue.
by|Oct 15, 2018
Q:What arch fault breakers do I need for this panel? I have not opened the box yet but is the 100 amp breaker that comes with this panel is protected as well? or do I need to put a whole house protection to my main panel? I am replacing an old 100 amp sub panel with this one I just received from Home Depot online order
by|Oct 12, 2018
2 Answers
Answer This Question
A: Only Siemens arc fault breakers
by|May 31, 2021
1 found this answer helpful
A: PW2020B1100CU accepts Types QAF and QAF2 arc fault breakers as listed on page 1-34 Speedfax catalog link below. These breakers provide arc fault protection only on the branch circuits they service. There are no AFCI mains offered. The only way to get whole house protection is to service each branch circuit with either an AFCI or dual function AFCI/GFCI breaker (Type QFGA2 as shown). This contrasts with surge protection in which full panel protection can be provided for all branch circuits by installing one surge protection breaker in a branch position as per instructions (refer to page 1-45).
https://w3.usa.siemens.com/powerdistribution/us/en/speedfax-product-catalog/Documents/2017/SF-17-Sect-01-ALL-web.pdf
by|Oct 23, 2018
1 found this answer helpful
Q:Can this panel be mounted only surface mount , or can it be flush mounted ??
by|Oct 11, 2018
2 Answers
Answer This Question
A: Partially. You need about 1 inch sticking out so the door can swing open. Of course considerations have to be made on wire access to the box when partially flush. See the factory site and Home Depots views on the box.
by|Apr 3, 2020
A: PW4040B1200CU has a combination type cover allowing either surface or semi-flush mounting. It cannot be fully flush mounted as this would prevent the hinged cover from opening properly.
by|Oct 12, 2018
Q:Can this be used as a sub panel?
by|Oct 3, 2018
2 Answers
Answer This Question
A: Yes, either as a main breaker or main lug with the ECMLK125 conversion kit. Ensure green bonding screw is removed for non-service entrance applications. To download the wiring diagram for this item go to link below and click on "Downloads" and enter PW2020B1100CU in the search box.
https://w3.usa.siemens.com/powerdistribution/us/en/Pages/low-medium-voltage.aspx
by|Jun 6, 2021
1 found this answer helpful
A: Yes
by|May 31, 2021
1 found this answer helpful
Q:does it come with the 100 amp main breaker
by|Aug 18, 2018
3 Answers
Answer This Question
A: Yes PW2020B1100CU includes a 100A main breaker. To download the cut sheet for PW2020B1100CU which confirms this, go to link below and click on "Downloads" and enter PW2020B1100CU in the search box. http://w3.usa.siemens.com/powerdistribution/us/en/Pages/low-medium-voltage.aspx
by|Jan 24, 2021
1 found this answer helpful
A: 100 amp main breaker is factory installed.
by|May 31, 2021
1 found this answer helpful
A: No, one is not included.
by|May 31, 2021
Q:does it come with the 100 amp main breaker
by|Aug 18, 2018
3 Answers
Answer This Question
A: Yes PW2020B1100CU includes a 100A main breaker.
To download the cut sheet for PW2020B1100CU which confirms this, go to link below and click on "Downloads" and enter PW2020B1100CU in the search box.
http://w3.usa.siemens.com/powerdistribution/us/en/Pages/low-medium-voltage.aspx
by|Jan 24, 2021
1 found this answer helpful
A: 100 amp main breaker is factory installed.
by|May 31, 2021
1 found this answer helpful
A: No, this product is a load center and does not include the breaker.