Questions and Answers for SharkBite 1/2 in. Push-to-Connect x 3/8 in. O.D. Compression Chrome-Plated Brass Quarter-Turn Angle Stop Valve

A:  USA

A:  Hello, SharkBite angle stop model # 23036-0000LF is an imported product. If you have additional questions please feel free to contact our customer service department at 877-700-4242. Best Regards,

A:  USA.

A:  China says on back of package

A:  Package reads made in USA. You can tell it is not China junk by operation of valve and weight of item, Not flimsy metal.

A:  I believe they are made in Cullman, Alabama, USA. https://youtu.be/_kTKuLd_S1o

A:  Angle stop

A:  I do not know your exact situation with respect to your ability to access to the pex supply pipe behind your drywall. Normally I would transition to a short 1/2" copper pipe from the pex using the Sharkbite 1/2 in Push-to-connect Brass coupling fitting (Model #U008LFA) bite behind the drywall. And then secure the copper pipe to a stud behind the drywall and extend the copper pipe out into the toilet area and connect it to the stop valve.

A:  Pex pipe can be painted with a vinyl paint or you could wrap it with silver duct tape.

A:  Hello, SharkBite PEX tubing may be painted with latex paint as long as the paint does not contain solvents. Another option would be to cover the PEX tubing with a cover tube designed for use with 1/2" nominal size pipe/tubing. Please be aware that we do not recommend the use of adhesives with our PEX tubing. If you have additional questions regarding the use of this product please feel free to contact our technical support department at 877-700-4242. Best Regards,

A:  Most people shorten the plumbing line coming out of the floor or wall, so you really only see the valve and then install a braided metal line / hose 12 - 18 inch. Before you install the valve onto the line, you can slide a decorative cover bezzle over the line and this addresses the unsightly hole in the wall or ground where the pipe comes through. Hope this helps.

A:  the outgoing water supply line to you faucet or fixture,

A:  That is a compression fitting...... but you can remove the nut and compression piece and put a braided line which is much easier.

A:  You can remove the nut and ferrule ( the brass thing under the nut) and attach a 3/8 flexible supply line.

A:  if you were doing tubing and using a flare connection

A:  Hello, The outlet nut is used in conjunction with the ferrule when used with 3/8" O.D. copper tubing. The nut and ferrule can be removed from the valve's outlet for use with 3/8" female compression threaded braided supply hoses. If you have additional questions please feel free to contact our technical support department at 877-700-4242. Best Regards,

A:  Hello, Unfortunately, SharkBite angle stop model # 23036-0000LF is not suitable for use with polybutylene tubing. It will first be necessary to transition from the polybutylene tubing to an approved type of pipe/tubing by using our polybutylene conversion coupling (link below). If you have additional questions please feel free to contact our technical support department at 877-700-4242. https://www.homedepot.com/p/SharkBite-1-2-in-Push-to-Connect-Brass-Polybutylene-Conversion-Coupling-Fitting-U4008LFA/202270632 Best Regards,

A:  It should but I’d be wary with all of the other issues that piping has had. Leave the plastic sleeve inside the fitting when using it with that pipe.

A:  I doubt it will work on that because it has an internal clap ring which bites on the pipe/plastic. The pipe goes on the inside of the fitting while the polybutylene goes on the outside of the fitting with a clamp over it.

A:  I like shark bit because it is fast and perfect for do it yourself but just make sure you push fitting on properly. They do sell a tool to make sure you push on far enough.

A:  As long as the 1/2" Push to connect matches the polybutylene pipe size you are using it should work fine. The other connection which is a compression fitting is meant for soft metal type pipe.

A:  You can cut off the old behind the nut if you has an inch of pipe left for the new valve to slip on. Clean with emery cloth and make sure no burrs on the pipie before installing new valve

A:  We need more information to properly assist you. Please contact Customer Service M-F, 8am-5pm at (877) 700-4242.

A:  If your pipe coming from the wall is threaded you need the same type of valve. The push-on will only work on a bare pipe.Plastic or metal. Take the flex pipe off and then the valve.Be sure to hold the pipe when turning the valve.

A:  i recommend getting a new compression valve and reuse old nut and feral that will not come off pipe without cutting pipe

A:  It’s actually not too hard to take off. The ring compresses when you tighten it. I was able to spin mine off. I used this shark bite fitting because it was easier to install and it’s a lot easier to service anytime you have a leak it’s only a 1/4 turn in comparison to 20 turns to close the valve and after a while the internals go out on those old valves and you get a leak from the nut itself. This one is more like a connect and you’re done. You will feel when its hooked on completely. I would get a shark bite disconnect tool. They have different things to clean the copper. You can use some steel wool type cleaner or sand paper to clean up the pipe but you mainly want to debur the edges especially if you cut the pipe.They have a tool for that. Below are some tools you can use that I actually used. They sale these tools at your local home improvement stores. If you have any other questions feel free to ask.

A:  It depends. Some compression fittings mash the compression ring into the pipe and make it almost impossible to get the old ring and nut off the pipe. That happened to me recently. So, as you said, I got a new compression fitting and used the existing compression ring and nut that were stuck on the pipe. It worked just fine. But some compression rings come off. You might want to see if yours is stuck or not before deciding.

A:  I replaced 5 existing values that was built in 1987. Make sure you clean the pipe really well, everything came off easily and installation was straight forward.

A:  No you get the valve only. You should be able to deburr using normal processes. Clean the copper with Emery cloth. The depth is important. On 1/2" copper tubing the depth is 15/16" and you should mark the pipe with a Sharpie or pencil line (if your eyes are good). Do not skip the pipe marking. I have the depth tool and I strongly encourage you have one and use it every time.

A:  My valve did not come with the removal tool. And the removal tool is not the same as the measurement tool. The removal tool is only for removing the SharkBite valve or other connection and the measurement tool is to show to what distance the SharkBite valve should slide onto the piping.

A:  No, it's sold separately. Yes, it is also for measuring. I was hesitant to purchase it because I thought I could just use other tolls but I am glad I did, it really leaves the surface very smooth. I tried with a filing paper before opening the burr tool bag, it was OK but it was much better with the orange tool.

A:  Two different tools. Removal tool is $1.95, depth tool is approx $10.00.

A:  No it does not come with the valve. It’s sold separately. I doubt it’s the same tool but it is a useful way to measure depth. I use it on occasion to measure the depth. I believe the picture below is what you speak of correct?

A:  I do not recall receiving any orange burr removal tool...just the valve.

A:  no to both questions

A:  The burr removal tool does not come with the valve. Burr removal tool is used to determine depth. If you don't have one its worth the few dollars it costs. I did all my plumbing with pex so burrs were not a problem but the depth tool made it a breeze. Put it on end of pipe, marked with a sharpie and knew that my fitting was all the way on. replumbed my whole place with pex and sharkbite push to connect fittings not one leak. Been over a year and still no leaks.

A:  No

A:  No, our safe seal tool does not come with any fitting. Yes, the safe seal tool is used for both de-burring the pipe and marking the correct insertion depth. If you have further questions, please contact Customer Service M-F, 8am-5pm at (877) 700-4242.

A:  Absolutely. Recently remodeled a bathroom replacing the tub with a sterling tub and surround back and re-plumbed all the tubs behind the way plumbing using shark bite connections. I initially bought shark bite look alike products and three of those four connectors leaked so I replaced all four with Shark bite products and sixteen months later no issues.

A:  Yes. They work great in that application. I recently used all SharkBite Pex tubing and fittings for my new shower valve assembly. (Moen)

A:  Yes they can. In fact, that’s exactly what I did. My wife and I remodeled our master bath last year and I installed the Shark Bite valves in the shower wall. I’ve had no problems what-so-ever. I also moved my single vanity from one wall and installed a double vanity on another wall. My house is on a slab so it required breaking the cement slab to access and reroute the water lines and plumbing. I converted my copper piping to pex and used all Shark Bite fittings for connections. In order to protect the fittings from the gravel and dirt, I covered them with NASHUA S&S Red Silicone Tape for the “Hot” connections and NASHUA S&S Blue Silicone Tape for the cold connections. Of course all fittings and tape was purchased at Hone Depot. Sorry for rambling on. I hope this helps.

A:  I have never had one leak. But this would would be a question for the manufacture.

A:  yes they can be enclosed in walls and are approved for use in any place you would use copper, cpvc or pex water lines and are considered a permanent fitting.

A:  Yes, I used some sharkbite connectors and flexible braided hoses for a shower valve. I eliminated about 11 solder joints, and the system has been functioning flawlessly for a couple of years now. Just be sure to cut the copper pipe square and brighten the contact point with emery cloth..

A:  SharkBite push-fit fittings are certified for use within a concealed wall, but consulting with local plumbing codes is recommended for specific applications. It is also recommended to pressure test the system prior to sealing up the wall. If you have further questions, please contact Customer Service M-F, 8am-5pm at (877) 700-4242.

A:  I am not a certified plumber but I have used a few for behind the wall and haven’t had any problems. I actually have 4 for my shower. 2 of them are valves for the water and 2 are ball valves that I use to shut off water in case I need to work on shower and don’t want to turn off main water from the city. Once you install you can open water and check for leaks. If you find any drop of water I would redo the lines. I haven’t had any leaks or problems though.

A:  They will tell you not to do that. But I have used them in that position and have had no issue's.

A:  No. I've been lucky to date and not needed one.

A:  Yes, the chrome ring that covers the collar can be removed, turned around and used as your disconnect clip. You can also use one of our orange disconnect clips that are sold by size. If you have further questions, please contact Customer Service M-F, 8am-5pm at (877) 700-4242.

A:  No it does not come with the tool. The piece hat is on there is to hide the connection and give it a clean look.

A:  The following copied from SharkBite web site "question/answer" section : Mike 3 yr ago I need to remove the angle stop from the 1/2" copper tube on which it is installed. How do you remove it? What is the disconnect tool referenced in the above information? I have the 1/4" horseshoe tool that came with the kit but nothing for 1/2". Answer this Question SharkBiteGM · 3 years ago Greetings Mike, To disconnect our SharkBite fittings, you will need a disconnect clip (orange horseshoe) that fits over your pipe. If you have 1/2” pipe, you will need a 1/2" disconnect clip. If you are using one of our angle stops, you can use the chrome plated clip attached on the SharkBite side. You pop it off, turn it around, set it on the pipe then press the collar in. If you are having issue or need immediate assistance, please call us at 1-877-700-4242 between 8am – 8pm EST.

A:  No the removal tool didn’t come with it. It just snaps into place and locks in.

A:  Insertion depth will depend on the size of the fitting. 1/4″ Pipe Insertion Depth = 13/16″ 3/8″ Pipe Insertion Depth = 15/16″ 1/2″ Pipe Insertion Depth = 15/16″ 5/8″ Pipe Insertion Depth = 1-1/8″ 3/4″ Pipe Insertion Depth = 1-1/8″ 1″ Pipe Insertion Depth = 1-5/16″ Source: http://www.sharkbite.com/resources/faqs/fittings/

A:  Found some data about this on a Sharkbite faq on their web site. The FAQ can be quite useful ;) See: http://www.sharkbite.com/resources/faqs/fittings/ also see http://www.sharkbite.com/sharkbite/wp-content/uploads/SharkBite_Installation_Instructions_2018_WEB.pdf Q: What is the insertion depth for the SharkBite fittings? A: Insertion depth will depend on the size of the fitting. 1/4″ Pipe Insertion Depth = 13/16″ 3/8″ Pipe Insertion Depth = 15/16″ 1/2″ Pipe Insertion Depth = 15/16″ 5/8″ Pipe Insertion Depth = 1-1/8″ 3/4″ Pipe Insertion Depth = 1-1/8″ 1″ Pipe Insertion Depth = 1-5/16″

A:  The insertion depth of this unit is 0.938 inches.

A:  That is actually 2 different questions. First, a 1/2 inch fitting has an insertion depth of 15/16 of an inch. You should mark that on the pipe before installing since there are several points where it may seem to be on completely, but it is not until it is seated at that depth. And it will not work unless it is properly seated. Second, there are several different tools that can be used to release the fitting, and they vary in size, so the only answer is that it is necessary to place them behind the fitting and to be able to be grasped adequately to pull them into the fitting in order to release it.

A:  I completely redid all the plumbing in my 2 mobile homes. I used pex pipe and all sharkbite push to connect fittings. Easiest plumbing i ever did. As per the instructions with any type of pipe, mark 1" from the end of the pipe. Push your fitting or valve onto the pipe up to your mark. Done. Sharkbite sells a deburring tool for a few different size pipe. It is also a depth guage. It goes on your pipe exactly an inch, mark it. No guess work.

A:  Insertion depth is based on the size of the fitting: •1/4″ Pipe Insertion Depth = 13/16″ •3/8″ Pipe Insertion Depth = 15/16″ •1/2″ Pipe Insertion Depth = 15/16″ •5/8″ Pipe Insertion Depth = 1-1/8″ •3/4″ Pipe Insertion Depth = 1-1/8″ •1″ Pipe Insertion Depth = 1-5/16″ We have disconnect clips for each size as well as disconnect tongs for 1/2", 3/4" and 1". If you have further questions, please contact Customer Service M-F, 8am-5pm at (877) 700-4242.

A:  July 31, 2018 - To date: Grandpa has the closest to the correct answer; However, still incomplete ;) Grandpa mentions the correct insertion depth for the angle stop and he "kind of" mentions an additional length of pipe required to remove the angle stop :) 1st) I can only guess that the 15/16" insertion marking in for the angle stop including the attached removal tool; but, that is not clear. 2nd) If cut my copper pipe 1 " from the wall and insert the angle stop; how would I remove it. Neither, Sharkbite or Grandpa takes into consideration the amount of pipe needed to utilize either the attached removal tool or the separately purchased removal tool. If I install the angle stop valve 1" (15/16" / .938") from the wall, how the heck do I remove it ? The Home Depot ad we are looking at is misleading as it does not make it clear that the removal tool is on the angle stop pictured and it does not mention in it's instructions either angle stop insertion point length or the required amount of pipe to utilize the attached removal tool. Furthermore, they picture 3 items frequently purchased together. The first two items are angle stops that have removal tools attached and the third would not be needed as it is an additional Sharkbite removal tool. My apologies if I am mistaken ? What is the total length of copper pipe needed to install and be able to remove the advertised item (angle stop valve) ? I am probably older than Grandpa ;) And I imagine I have less plumbing experience and as normal in DIY(er) projects, I am quite Honestly confused. Note: My bad valve was soldered on in 1973 and the distance from a flush cut at the valve to the Escutcheon (wall plate trim) is a tight close quartered 1.5 inches. The rubber end of the valve stem broke apart and ended up in the upper part of the flush valve. The handle screw is corroded in place and I crushed the handle with channel-locks trying to turn off the water when the flush valve leaked due to the rubber pieces keeping it from shutting off. My Original Question: AKA: What is minimum length of copper pipe needed for install & removal tool ?

A:  Answers here are mostly incorrect. If you get the "plastic C-shaped" ring with your component (it comes with most of the chrome plated brass components) it is not only a "cosmetic cover" but is intended to be used to remove the component if needed. Simply take it off of the pipe, reverse it, and then press it onto fitting thereby releasing the grip of the fitting allowing it to be removed from the pipe.

A:  The plastic piece is designed to simply hide the connection between the valve body and the hose. Simply cosmetic. It has nothing to do with the valve performance or integrity.

A:  It provides a bit of a cover for the joint to make the finished product look nicer. It also functions as a removal tool...take the clip off turn it around and place it back on the pipe/angle stop and push in to the end of the stop while pulling it off.

A:  Its used to remove valve if ever needed.You pull back against the valve and it slides off, they also make a tool for doing to!

A:  I may be mistaken; but, I believe the answers are related to something different than what is asked. I believe the question relates to the orange separately priced removal tool; not the chrome one that is included with this push-on valve. I think "bite" is misspelled meaning "buy it" area where 3 parts listed across page; the third being the orange removal tool and the first two being valves that include the removal tool (it is attached to the valve in the pictures). Neither are just decorative items; but, could prevent unwanted dust or splatters from polluting the top and sides of the valve in addition to the valve removal function. The following copied from SharkBite web site "question/answer" section : Mike 3 yr ago I need to remove the angle stop from the 1/2" copper tube on which it is installed. How do you remove it? What is the disconnect tool referenced in the above information? I have the 1/4" horseshoe tool that came with the kit but nothing for 1/2". Answer this Question SharkBiteGM · 3 years ago Greetings Mike, To disconnect our SharkBite fittings, you will need a disconnect clip (orange horseshoe) that fits over your pipe. If you have 1/2” pipe, you will need a 1/2" disconnect clip. If you are using one of our angle stops, you can use the chrome plated clip attached on the SharkBite side. You pop it off, turn it around, set it on the pipe then press the collar in. If you are having issue or need immediate assistance, please call us at 1-877-700-4242 between 8am – 8pm EST.

A:  It's just a collar that hides the actual connection. It doesn't serve anything mechanical. It's strictly cosmetic.

A:  It's just a decorative ring to cover the connection. It's C-Shaped so you can get it on after the connection is made.

A:  It is a cover that can snap on and cover the collar of the fitting where the pipe is inserted. It can also be rotated and used as a disconnect clip. If you have further questions, please contact Customer Service M-F, 8am-5pm at (877) 700-4242.

A:  It is just for looks, "asthetics" perhaps.

A:  The plastic c shaped chrome peice is just for looks , it’s basically just to trim around where the plumbing pipe meets the fitting, it has no effect on the functionality of the valve