Q:Does anyone know the dimensions of the rectangles?
by|Sep 3, 2021
1 Answer
Answer This Question
A: Hello Brian
Thank you for your contact. We apologize for any trouble or inconvenience in finding information. Dimensions are for the whole insert. This is customizable by removing the blocks or grids as suited to fit your needs.
Best Regards
Sherri C
DEWALT
by|Sep 10, 2021
Q:What are the overall dimensions of this item?
by|Jun 15, 2021
1 Answer
Answer This Question
A: Hello Razor,
Thank you for your contact. We apologize for any trouble or inconvenience in finding information. The dimension for the storage organizer is 16-7/8″ W x 2-11/16″ H x 11-13/16″ D.
Best Regards
Sherri C
DEWALT
by|Jun 16, 2021
Q:Will these also fit Craftsman versastack boxes?
by|Dec 8, 2020
2 Answers
Answer This Question
A: Not 100% sure but they look exactly the same the Craftsman and the Dewalt 17"
I would get you can always send it back if it is not right.
But they look the same I compared the Craftsman to the one I have. I pulled out the foam to make the cutouts I needed and then sprayed it with Plasti Dip. That gave it a waterproof more durable finish.
by|Dec 9, 2020
A: Yes. I had to trim a bit to fit the clear lid box but the other tool box fits fine.
by|Jan 28, 2021
Q:how many dewalt TSTAK foam inserts do you get for$10.48. the picture shown, appears to be several stacked together. Thanks
by|Apr 14, 2019
4 Answers
Answer This Question
A: Just one to fill up the small TSTAK case. It is layers of foam so it makes it easier to customize the insert to the tools or whatever you put inside.
by|Mar 31, 2020
1 found this answer helpful
A: One
by|Dec 9, 2020
A: The image is for one, complete, unit. The multiple layers are all glued together into one unit. Each "little square" is actually a "cube" of foam that you can "pick" out with your fingers...you can pick a layer deep...or multiple layers deep. great if you need to form "ledges" and "valleys".
by|Jan 18, 2021
2 found this answer helpful
A: You gey one insert about 2 1/2" thick. It is made up of 6 thinner pieces glued together. I think they do this to make the partial pre-cut grid system work.
by|Sep 9, 2020
Q:Will this insert fit the toughsystem boxes?
by|Feb 23, 2018
4 Answers
Answer This Question
A: No, too small. I am pretty sure the tough box has their own version.
by|Jan 18, 2021
3 found this answer helpful
A: Yes it will, matches most if not all of the stacking units! love them for saving my tools. Not like that junky bags that comes with the expensive DeWalt tools!
by|Jan 18, 2021
A: Tough systems are 22" the Tstak is 17"
by|Jan 18, 2021
1 found this answer helpful
A: absolutely
by|Jan 18, 2021
Q:What size are the removable squares?
by|Jan 14, 2018
7 Answers
Answer This Question
A: I did not specifically measure but either 1/2” or maybe 5/8 in
by|May 5, 2023
A: 1" approximately
by|May 5, 2023
A: about 5/8" square
by|May 5, 2023
A: The "squares" are roughly 1/2" on all sides....and as deep as one layer of foam. The "stack" is made up of several (7 or 8) layers of foam. (each layer is roughly 1/4" thick. I used a thin blade X-acto knife to cut along the cube score-lines. The bottom layer isn't scored so it acts as a final bottom base layer. You can remove as many layers as you like in any combination.
by|May 5, 2023
1 found this answer helpful
A: The squares are about 3/4" square.
by|Nov 1, 2020
A: This worked great to hold tool in place after cutting . Each square is about 1/2 by 1/2 inch
by|May 5, 2023
A: The squares are 1/2 inch and are easily removed, I was concerned that if they could be removed so easily that they would fall out under everyday tool use once the foam was in service but I got the foam for the 20 volt max jigsaw with batts and charger and use it almost every day and the the foam is holding up better than I thought it would and it is now about three months.
by|May 5, 2023
Q:Can this be used in the drawers or it is only designed for the larger boxes?
by|May 16, 2017
3 Answers
Answer This Question
A: Made for the bigger boxes
by|Dec 9, 2020
A: I use this for any of my tool boxes, you also have to keep in mind that each case is design for different tools.
by|May 7, 2019
A: This is only designed to fit in the box.
by|May 4, 2023
Q:Do these fit into the TSTAK II 13 in. 1-Compartment Flat Top Stackable Tool Box snugly?
by|Jan 5, 2017
2 Answers
Answer This Question
A: Yes, the foam insert is designed to fit the DWST17807 (TSTAK II), DWST17808 (TSTAK I), DWST17805 (9 Compartment small parts box).
by|May 4, 2023
A: No these are 17" Though it is foam so you could cut it