A: yes , is water proof , easy to clean , just no close too heat
by|Apr 12, 2024
A: Hello Robert, FRP panels would be great to use on the inside of a food truck. But do not put them directly behind a stove or any other area that would be exposed to high temperatures. The panels will warp and burn. Thank you, -Stabilit America
by|Mar 21, 2024
Q:Could this be use in a shower
by|Mar 18, 2024
2 Answers
Answer This Question
A: yes , but you need seal all corner with silicon
by|Apr 13, 2024
A: Hello Darryl, Yes, these panels can be used for shower walls. As long as the joints are sealed with a silicone caulk then you should be good to go. Thanks, -Stabilit America
by|Mar 19, 2024
Q:What’s the heat rating?
by|Mar 18, 2024
1 Answer
Answer This Question
A: Hello FDquestion, The panels we sell in Home Depot stores are rated as a Class - C, general purpose panel. FRP will withstand temperature extremes of –65°F to +212°F. It will however, expand or contract with temperature variations. We do offer a Class - A, fire retardant panel through Home Depot's Special Order program. Thank you, -Stabilit America
by|Mar 19, 2024
Q:What kind of backing material is best? Green board, or durock?
by|Mar 12, 2024
3 Answers
Answer This Question
A: anione is ok , just used the right glue
by|Apr 12, 2024
A: any is ok , just found the rick glue
by|Apr 14, 2024
A: Hello Gary, If installing the FRP panels by adhesive, it is recommended the backing be a porous surface, such as concrete block, drywall, plywood or plaster walls. Thank you, -Stabilit America
by|Mar 12, 2024
Q:Can this be used in a garage?
by|Mar 3, 2024
1 Answer
Answer This Question
A: Hi, Yes, you can absolutely use this as a wall covering in a garage. It can be used in any indoor wall application. Thank you, -Stabilit America
by|Mar 4, 2024
Q:Will polyester or epoxy resin adhere to fiberglass reinforced plastic panels? Thanks.
by|Mar 1, 2024
1 Answer
Answer This Question
A: Hello David, The textured finish of the panel has a top coating meant to resist adhesion. Titebond solvent based adhesive might do the trick. It might be best to use plastic rivets. Just be sure to drill pilot holes. Thank you, - Stabilit America
by|Mar 9, 2024
1 found this answer helpful
Q:What do you use to connect 2 pieces together
by|Feb 26, 2024
1 Answer
Answer This Question
A: Hello Mick, Our Interior FRP Divider Bar Moulding - 99290XA (sku 471869) provides a transition piece between the panels. Thank you, - Stabilit America
by|Apr 1, 2024
Q:How do you install it? Rivets, nails,glue??
by|Feb 21, 2024
1 Answer
Answer This Question
A: Hello Eric, For installation instructions, please check out our product brochure on our website below: https://www.glasteel.com/wp-content/uploads/2020/01/Glasteel-Combo-Brochure_9-11-13.pdf
Also, Home Depot has put together a great FRP guide of their own. Check it out here: https://www.homedepot.com/c/ah/how-to-install-frp-paneling/9ba683603be9fa5395fab901f292fee3 Thank you, -Stabilit America
by|Feb 22, 2024
Q:Can it be painted?
by|Feb 8, 2024
1 Answer
Answer This Question
A: Hello Lisasawool, The finish is designed to be a non‐adherable surface. If painting is necessary, a high-quality epoxy or acrylic‐based paint is suggested. Thanks, -Stabilit America
by|Feb 9, 2024
Q:Will this block mold
by|Feb 2, 2024
1 Answer
Answer This Question
A: Hello Royb, FRP panels do not support the growth of mold or mildew. They are also impervious to most mild acids and alkalis. Normal cleaning procedures are recommended. Thank you, -Stabilit America