My Charbroil is 12 years old and after eleven years in New England, winters and all, with no cover, it needed some TLC. I looked at new grills but they are mostly stamped steel, while my grill is cast aluminum, so no need to replace the whole thing. The replacement burner works perfectly. People who complain about the screw sizes don't know what they are doing. Everything tightened up perfectly, and the gas feeder hoses extended more than enough to reach the controls. And the clamps provided are just as tight as the originals.
by
DIY
Recommended
3 found this review helpful
Apr 4, 2013
As Adertised
Took 10 minutes to install. Grill works like new. All screws were the correct size, I don't understand what some of the other reviewers are complaining about.
by
DIY
Recommended
3 found this review helpful
Oct 28, 2017
I’ve had this grill for several yrs and has always given superior service and still working great.
by
Response from SMEDec 22, 2023
Thank you for your review.
Recommended
Customer review from Char-Broil, LLC
Oct 26, 2017
needs to be thicker
I bought this a year ago and I well needs to replace it soon if you can make it a little thicker to last longer
by
Response from SMENov 15, 2023
Thank you for your review.
Recommended
Customer review from Char-Broil, LLC
Aug 19, 2017
Hard to adjust, uneven flame
Put together and tried to fit to a 90s Quickset Traditional. Could not get it to center or lay flat. Attached collector box, but it could not get enough gas to light. When lit, it burned yellow and uneven. Took it out and put in a Made In USA part from a 1980s grill I picked up in the trash and it still works great. This replacement part will keep you grilling, but not happy.
by
Response from SMENov 8, 2023
Whenever an issue is encountered give us a call at 1-866-239-6777 and we'll be able to further investigate and help.
Customer review from Char-Broil, LLC
Jan 15, 2016
Very well built burner
We use our grill about 3 times a week year round. We had a burner before from Char-Broil and were glad to buy this one from them.
by
Response from SMEMar 21, 2024
Thank you for your review.
Verified Purchase
Recommended
Customer review from Char-Broil, LLC
Aug 12, 2014
Good replacement
I ordered the burner on line. Picked it up at the store. N o problem putting it on my Char broil grill. Works fine.
by
DIY
Verified Purchase
Recommended
Jul 13, 2014
Home Depot was only place that had this Burner. Fit perfectly Thanks
Home Depot was the only place that had a burner to fit an old grill, fit Perfectly!
by
Pro
Verified Purchase
Recommended
Jul 8, 2014
How do I send this back
I ordered this burner because I have a CharBroil BBQ. The unit assembled easily enough but the gas prongs were too big to fit through the openings in the BBQ.
by
DIY
Verified Purchase
Nov 12, 2013
I should have purchased a second one for replacement in the future
Does everything in the add it claims too. I had no trouble adjusting to my 20 yr. old kenmore grill, I average about 2 to 2 1/2 yrs. life span on burners. Yeah I know its time to get a new grill but that old grill works just fine and is well seasoned!
by
DIY
Verified Purchase
Recommended
Sep 17, 2013
Great product but watch out for the tubes
The flex tubes are the weak link, and you can not buy them separately. The rest of this unit is great easy to install and very durable.
by
Verified Purchase
Recommended
Aug 13, 2013
This product is excellent.
This product is awsome because fit with all grills the feuture is this is telescopic after that you can setup and adjust exactly your measure.
by
Verified Purchase
Recommended
Jul 16, 2013
Fits "OK" on Thermos Millennium 3000 Grill -
It was not a quick replace install like the older model replacements HD use to sell. Putting together the parts was pretty basic and easy. The issue I had was with the width of the tubing attached to the burner. On-center, they were wider than the two molded-holes in the base of the grill by a good 3/4 inch. The tubing is made of flexi-aluminum so bending smooth curves to adjust to fit down through holes was frustrating because the tubing isn't all that "tough" and easy to dent. On the millennium 3000 there is a steel lava-rock grate the tubing has to pass through, but because of the offset, it sort of caused the burner to sit off center and back and slightly tilted upward. But after more bending, twisting, and futzing around, the burner tubes connected up and I got it to sit somewhat on center, but the tubing is slightly dented (like the fins on an AC unit can get) a tad here and there due to the moving back-forth-down-etc..The last hurdle was getting the tube-ends to stay on. After putting clips on, I stretched out the original tube clamp pins so the point hooked onto the lip at the end of the burner tube and it just caught enough to hold tube back onto gas-inlet stubs. In the end it works and burner is now spread across entire width of grill . Not sure how long it will all last, but cheaper than getting new grill.
by
Verified Purchase
Recommended
May 1, 2013
didnt fit the openings to the on/off knobs on a char broil grill
this replacement burner would have been just what i needed had the flex tubes fit the openings in the cast iron shell of the grill base that the on/off knobs connect to. they are too wide around and i just didnt feel like getting a drill out and fiddling with the grill .... i have hated the grill for the last 9 years anyway so instead of replacing the burner i bought a new grill.
by
DIY
Verified Purchase
Recommended
Jun 3, 2012
A GREAT REPLACEMENT
The Char-Broil Universal Replacement Bar Burner is manufactured of heavy-duty 430 stainless steel with built-in spider/insect guards it's Easy to install and well worth the price!
by
Recommended
1 found this review helpful
May 1, 2012
OK for the price
Just take your time and this is a no brainer to put together and install.
by
Recommended
2 found this review helpful
Apr 25, 2012
Good for Your Pocket
The product was great for the money and should fit any grill size.
by
Pro
Verified Purchase
Recommended
May 26, 2011
Baton Rouge customer is right! Do NOT buy this item! _________ NO STARS!
Baton Rouge customer is right! I should have learned from what he wrote.
This Char Broil burner replacement kit is a waste of time and money. The tiny screws provided for the very first assembly step are TOO BIG for the double set of holes they are supposed to fit into! Unless the screws are inserted, the holes won't line up and the propane gas will not flow out of them!
What a waste of time!
I will return this replacement kit to the store and explain to the clerk this item's short-comings so that Home Depot purchasing agents notice.
DO *NOT* BUY THIS ITEM!
by
21 found this review helpful
Oct 24, 2010
Should have gone elsewhere-
This was the only product in the store that would fit my grill. Wish I had gone elsewhere and maybe gotten a different one. The screws and holes for the screws are not a match in size. Stripped out some of the screws trying to get it together. Also, the gas connections are flimsy though I understand they are meant to be flexible so to fit various styles of grills. This is a product to avoid unless there are no other options and you can pick up some screws while you are at the store so as not to have to make two trips.