Q:how do you attach the bottom brace if my house is brick?
by|Apr 11, 2021
2 Answers
Answer This Question
A: the braces usually attached to the roof under shingle tabs.
by|Apr 13, 2021
A: Please contact Customer Care at 888-523-3371, so the installation instructions can be emailed to you.
by|Apr 12, 2021
Q:Is price per each brace or does 2 come per order as reviewer noted?
by|Sep 10, 2018
5 Answers
Answer This Question
A: Only One brace per box.
by|May 6, 2023
A: As the other answers stated only one to a box.
by|May 6, 2023
A: Price is for each. Well worth it.
by|May 6, 2023
A: "Dear Valued Home Depot Customer, To better answer your question, please contact our HD.com Customer Service department at 800-430-3376. Call any day between 6 a.m. and 2 p.m. EST, or call your local store. They can either answer your question or transfer you to your local store to answer your specific question."
by|Jun 27, 2019
A: per brace just as per jack
by|May 6, 2023
Q:Is there a roof brace available for this same system? (Wood poles)
by|Jul 11, 2017
1 Answer
Answer This Question
A: Hi Climber4Life83,
We do not offer the wood version of the Pump Jack Foldable Brace on Homedepot.com.
Thanks for shopping Home Depot!
by|Jul 12, 2017
Q:Can these be used to secure top of poles to roof instead of wall?
by|Jul 11, 2017
2 Answers
Answer This Question
A: The SPJ-SBF cannot be secured to the top of a roof. Please go to the following link, to see
the user guide:
http://www.wernerco.com/docs/us/userguides/spj-sbf.pdf?Status=Master&sfvrsn=2
Installation of Pole Braces:
1.Loosen wing nut on brace clamp bolt and slide clamp
plates around top of each wood pole, ensuring seam of
wood pole is facing work wall. Tighten wing nut when
brace is at desired height and fasten brace clamp plates
to pole.
2.Position poles in desired location along work wall and
secure each pole to work wall with brace at top of pole.
Ensure round leg of brace is attached to work wall
straight out from pole and is fastened to work wall using
at least two screws with a minimum holding strength
equivalent to 1/4 inch x 3 inch, type AB screws. The
angle bar of brace can be fastened to either the right or
the left as desired and must be fastened to work wall
using at least two screws with a minimum holding
strength equivalent to 1/4 inch x 3 inch, type AB screws.
The two arms of the brace have been designed with 32
inch spacing to allow them to be attached to work wall on
studs spaced at 16 inch centers.
3.Stabilize bottom of pole by using either a pole anchor, or
by placing with a level piece of wood under pole.
4.Install pole brace at bottom of pole and other locations as
required. Poles must be supported by a pole brace at
top, bottom and every 10 feet in between.
by|Nov 6, 2020
1 found this answer helpful
A: Yes. They are designed for wall or roof mounting.
by|Jul 7, 2022
1 found this answer helpful
Q:Werner states that the distance the "support brace can hold the 4x4 away from the building is 14" maximum". How is that remotely possible if the pump jack can accommodate a platform of up to 24" in width ??? Werner, please explain the discrepancy.
by|Feb 20, 2017
1 Answer
Answer This Question
A: Please contact Customer Care at 888-523-3370 Monday through Friday from 8:00 AM to 5:00 PM EST. We will need to know where you obtained this information.
by|May 4, 2023
Q:will this brace also work with the qualcraft system?
by|Jun 17, 2016
1 Answer
Answer This Question
A: Our pump jack system has not been tested to be used with the qualcraft system, and is not recommend for this application.
by|May 3, 2023
Q:How far do these braces hold the 4x4 from the building?
by|Feb 22, 2016
3 Answers
Answer This Question
A: The extended length the foldable support brace can hold the 4x4 away from the building is 14" maximum.
by|Sep 15, 2020
A: It depends on where you have them attached. If on the side wall, then the length of the round rod determines the offset. Likewise if on the roof, it is a function of how far on the roof you attach the brace, but remember, you want the pole vertical, so distance to the sidewall is the determining factor. The length of the round rod is 29".
by|May 6, 2023
A: For my application, there is 31 inches from the 4x4 to the wall. This gives plenty of room from the pump jack deck to the wall. The arms are long enough to allow for clearance between the wall and the jack deck in case you need to have the arms pivoted a little high or low. Aim to have the arms level, and you'll clear the deck with nearly a foot of room.