Questions and Answers for SharkBite 1/2 in. PEX Barb Stainless Steel Clamp (10-Pack)

A:  Hi, The SharkBite 1/2 in. PEX Barb Stainless Steel Clamp can be clamped with any tool that meets the (ASTM F2098) standard. You would need to verify that the tool you would like to use has been tested and approved to the standard. If you have any more questions you can call tech support at 877-700-4242. (Kind regards,)

A:  I always use them on B for potable water. red blue or white.

A:  I have used these crimp rings on pex b Tubing but they work on both a and B.

A:  Hello, SharkBite clamp rings are suitable for use with any PEX tubing that is approved for use with ASTM F2098 clamp rings (regardless of if the tubing is type A, B or C). It will be necessary look on the outside of your particular tubing to see if ASTM F2098 is printed on it. If not, we would recommend contacting the tubing's manufacturer to check for approval. All SharkBite PEX and PERT tubing is approved for use with these rings. If you have additional questions please don't hesitate to reach out to our technical support department at 877-700-4242. Best Regards,

A:  Not that I know of. The stainless steel clamps require a lot of force to set them properly and that is why the handles of the installation tool are so long.

A:  What is on the other side of the wall? I installed an access panel behind my shower faucet, easy to access all of the clamps. Sometimes you can disconnect other fittings and move your workpiece for better access.

A:  Yep

A:  Yes you need the tool. It sets the exact position and tension.

A:  Although it may seem like a quick solution, using the pliers will not fully crimp the clamp. The pex clamp tool is designed to equally crimp along the stainless offset to the proper amount. Don't chance a major leak from a blown off clamp!

A:  You have to use the pex clamp tool

A:  You need to use the proper tool for a leak free seal.

A:  You'll be needing a clamp tool for this.

A:  I won't say you can't, but you only get one chance and if it's not properly clamped - the Pex pipe can come off the fitting. If you plan to do several - the proper tool is the Pex Clamp Tool - well worth it in the long run.

A:  Hello, SharkBite PEX tubing is rated for a minimum temperature of 33°F at 160 psi and a maximum temperature of 200°F at 80 psi. If you have additional questions regarding this product please feel free to contact our technical support department at 877-700-4242. Best Regards,

A:  Depending on the pipe and manufacturer, those spec will be on the "specs" section of the description when you look at the item. That's the best way to know for sure.

A:  Coldest: Just above freezing Hottest: 200° F

A:  No this is for 1/2" pex only, just get the 3/8" clamps.

A:  no it will leak

A:  No, The clamp diameter needs to match the diameter of the PEX tubing

A:  No it is for 1/2" only

A:  Hello, 1/2" SharkBite clamp rings should only be used with 1/2" nominal size PEX tubing that has an outside diameter of 5/8". SharkBite 3/8" clamp rings should only be used with 3/8" nominal size PEX tubing with an outside diameter of 1/2". If you have additional questions please contact our technical support department at 877-700-4242. Regards

A:  Yes it is. For proper installation you should use our clamp tool. It will work on 3/8", 1/2", 3/4" and 1" diameter clamps. If you have further questions, please call Customer Service M-F, 8am-5pm at (877) 700-4242.

A:  It is a pinch clamp, not a cinch clamp.

A:  Yes.

A:  Yes, I believe that it is. And it does take a special tool to properly "cinch" it on the Pex hose and fitting.

A:  Yes it is and it is called that because it is putting tension on the clamp to seal the connection. Always use the proper crimping tool and follow all safety precautions.

A:  Yes but you will have to go to the lowes in Golden

A:  It is available in certain stores in larger quantities or you can order it at HomeDepot.com. If you have further questions, please contact Customer Service M-F, 8am -5pm at (877) 700-4242.