Q:Several reviewers claim that this arm is just powder coated “ Steel”?
Not Aluminum ?
by|Sep 15, 2020
1 Answer
Answer This Question
A: Yes. Weather resistant 12 " extruded aluminum.
by|Sep 18, 2020
1 found this answer helpful
Q:I have scoured the interwebs and come up empty.
by|Jun 2, 2018
2 Answers
Answer This Question
A: Your question is not relevant to this product(area light mounting arm). I would think to contact your light manufacturer for a replacement lens if Home Depot doesn't have them. Call the manufacturer. You'd be surprised. Sometimes a manufacturer may send you 1 for free.
by|May 5, 2023
A: Unfortunately, your question was posted under the listing for the aluminum mounting arm rather than under the listing for the light fixture itself. I was unable to identify the manufacturer or model number of the fixture. Examine the fixture to find the information plate ( it could be a plate or some type of sticker) which should identify the manufacturer and model. Once you have this information, call the manufacturer's customer service department, supply them with the model number and request the right lens.
by|May 5, 2023
Q:Will this arm fir this light
by|Dec 22, 2017
1 Answer
Answer This Question
A: Most likely. All area light fixtures have standard mounting capabilities to this type of mounting arm. Buy it and see. Home Depot has one great return policy if it doesn't fit.
by|May 5, 2023
Q:What is the weight limit on this arm?
by|Oct 29, 2017
0 Answer
Answer This Question
Q:Will this arm work with an LITHIONA Dust to Dawn 35W LED Dust to Dawn Security light and does mounting hardware come with the arm.
by|Jan 20, 2017
3 Answers
Answer This Question
A: The extension arm does work on several of the Lithonia dust to dawn lights that have the cast aluminum triangular mount, but a part number for the light is needed to be sure.
by|May 4, 2023
A: This mounting arm is compatible with most outdoor area lighting fixtures, both LED and non LED. However, since you did not specify a Lithonia model number, it is not possible to say with certainty. The arm comes with a mounting bracket and arm extension as shown in the listing. That is the only hardware supplied with it.
by|May 4, 2023
1 found this answer helpful
A: yes
by|May 5, 2023
Q:How would I run power from the wall junction box to the arm? Since there is no "face plate" associated with the arm I'm not clear on that. Can't just run bare wires. I get it on the lamp fixture connection, just need help from the junction box connection.
by|Dec 13, 2016
3 Answers
Answer This Question
A: In my case, I used #12 Underground wire (12-2 Gray Solid CU UF-B W/G Cable) and run the wire down the tube, out the bottom and then into the wall or down the pole to the box. The wire is extremely tough to nick or cut but if you have concerns you can run put the wire in PVC that goes right up into the tubing and then into a water tight box or other type of connection to the power source. This would even work in the case with the pole, just run the PVC down to the ground and then underground if needed and to the power source.
by|Jan 30, 2019
1 found this answer helpful
A: There is going to be an open cavity throughout the mounting arm and the fixture will have a knockout that u can slide your wire through once it's through the arm
by|May 4, 2023
1 found this answer helpful
A: We installed ours on our pole barn above our garage door and drilled a hole under the arm and the wire went into the hole and hooked direct to our other outside lights.
by|May 5, 2023
Q:need to know because light has a 56 mm connection for the bracket. The bracket slips inside the back side of the light head.
by|Oct 15, 2016
3 Answers
Answer This Question
A: The extension is made from a standard thin wall 2" pipe.
by|May 4, 2023
A: The diameter of the aluminum tube is 1.4 in.;, width of attachment bracket is 2in.; height of mounting arm is 9 in.; arm extends out 12 in.
by|May 4, 2023
1 found this answer helpful
A: 1-1/2 or 2 inches. There is a clamping device so it should not matter
by|May 5, 2023
Q:Can this Lithonia Mount Arm #OMA M6, Store SKU#596808 be used with the Lithonia area LED light #OLA240K120 PER M4, Store SKU# 1000991132?
by|Feb 9, 2016
2 Answers
Answer This Question
A: Yes, this arm will fit that model of Lithonia Light.
by|May 4, 2023
A: Yes, this mounting arm is compatible with the area LED light mentioned.