Questions and Answers for KRAUS Rectangular Ceramic Vessel Bathroom Sink in White

A:  Check the manual/ installation instructions shown online in the overview tab for the sink. If you have the countertop made make sure that the measurements of the holes between sink and faucet are correct. Too far and you are washing your hands all the way ‘in the back’ of the sink.

A:  These dimensions are totally dependant on style and brand. Nearly all faucets will fit within a 45mm (1-3/4") hole centered 2" from the backsplash. If installing on a granite surface a 45mm hole will work for the drain as well. For counter tops of other materials a 4" hole is recommended to secure the drain directly to the sink. The back edge of the sink is 2-1/2" from the faucet hole centerline.

A:  Hi ja, Thanks for reaching out. Our KCV-121 is designed to lay flat onto the counter and not intended to rest as a recessed (or semi-recessed) sink. We recommend a 5" diameter hole in your counter to ensure you have enough space for the concave washer of the drain to be pressed up directly against the bottom of the sink. We also recommend installing your faucet 2" to 4" inches behind the sink. Please feel free to reach out to us at 800-775-0703 or email us at customerservice@kraususa.com with any additional questions. Happy to assist. Best, Mike Kraus USA

A:  You can drill the hole for the sink any size that is a bit larger than the drain. It will be covered by the sink so it really does not matter. As for the faucet, I would set the sink with the drain attached and then place the faucet where you want it. Then drill the hole the size that the manufacturer of the faucet recommends.

A:  its a surface mount sink, you do not cut a hole

A:  Hi Kaz1, Thank you for your inquiry. Our pop-up drains when installed with a ceramic sink requires a larger hole size so that the washers can create an airtight seal. The hole size required can go between 3.5" to 5". We would not have another drain available for our ceramic sinks that would require a smaller size drain hole. If you have any further questions please contact us at 1-800-775-0703 or customerservice@krausua.com. Best Regards, Anna Kraus USA Customer Support

A:  The outside height is 5''.

A:  Hi DS, Thanks for reaching out to us. The sink itself measures 5" from the base of the drain (under sink) to the top of the sink. Also, the distance from the top of the sink to the base of the bowl (internal surface) is 3.75". Hope this helps. Please feel free to contact us at 1-800-775-0703 or email us at customerservice@kraususa.com with any questions. Happy to assist. Best, Mike Kraus USA

A:  Yes, it can.

A:  Yes, dependent on drain hole location from rear wall and length of faucet down spout.

A:  Thanks for your inquiry. Yes - A wall mounted faucet can be used with our KCV-121 with no problem. Please feel free to reach out to us at 800-775-0703 or via email at customerservice@kraususa.com with any additional questions. Happy to assist. Best, Mike Kraus USA

A:  Ya I don’t see why not

A:  Yup! That’s what mine is

A:  Hi katho, Thanks for your inquiry. Yes, this sink and drain combination are also available in Satin Nickel. Please search under: KCV-121-SN Please also feel free to call us at 800-775-0703 or email us at customerservice@kraususa.com with any questions. We’d be happy to assist you. Best, Mike Kraus USA

A:  No, this model does not come with a brushed nickel drain.

A:  yes it does.

A:  Not to my knowledge. I used it with the chrome drain & a brushed stainless faucet. It looks great! Given the height if the bowl, you barely notice the drain.

A:  I installed two of these sinks on a 22 inch countertop and was able to put the faucets behind the sinks but it is tight. 17" depth will not allow enough space for faucet unless the faucet is coming out of the wall above the sink.

A:  Our counter is 22” wide I think it would not work you need space for the faucet and it has to be tall to go over the sink and the support is essential

A:  I purchased this sink and have it installed. 17" would not be enough room for the faucet install at rear of sink.

A:  yes but it will leave a gap behind that will get dirty and hard to clean

A:  Hi ksg06, Thanks for your inquiry. We recommend a minimum of 4.5” from wall to edge of sink for faucet placement clearance. At 17" it would be a very tight space. Oue KCV-121 also has a weight of 26.1 lbs.Please also feel free to call us at 800-775-0703 or email us at customerservice@kraususa.com with any questions. We’d be happy to assist you. Best, Mike Kraus USA

A:  Put the faucet on the side We mounted our sink in a diamond shape and put the faucet on the side It’s your vanity and house. Do want u want We have a square and a rectangle sink from kraus. And its pretty darn heavy

A:  This sink is designed with a standard 1.75 inch drain opening that works with pop-up drains without overflow.

A:  Hi elle, Thanks for your inquiry. Our KCV-122 does not have overflow. Please also feel free to call us at 800-775-0703 or email us at customerservice@kraususa.com with any questions. We’d be happy to assist you. Best, Mike Kraus USA

A:  No it does not have an overflow.

A:  No overflow.

A:  Hi elle, Thanks for your inquiry. Our KCV-122 does not have overflow. Please also feel free to call us at 800-775-0703 or email us at customerservice@kraususa.com with any questions. We’d be happy to assist you. Best, Mike Kraus USA

A:  Nope.

A:  A complete installation guide can be viewed via a link on the right-hand side of the product page in order to help you determine if this product will suit your project needs.

A:  Thanks for your inquiry. Yes, the our KCV-122 does sit flat on the counter top and the only hole required is a 5" diameter hole for the drain. Also, we recommend using waterproof silicone around the perimeter of the sink to provide additional stability. Please also feel free to call us at 800-775-0703 or email us at customerservice@kraususa.com with any questions. We’d be happy to assist you. Best, Mike Kraus USA

A:  Hi JD, Thanks for your inquiry. This is also our Kraus Pop-Up Drain (model # PU-10). Please also feel free to call us at 800-775-0703 or email us at customerservice@kraususa.com with any questions. We’d be happy to assist you. Best, Mike Kraus USA