A: For the Everbilt 1-1/4 in. x 48 in. Zinc-Plated Punched Angle, 1” is the distance between holes center-to-center.
by|Feb 29, 2024
3 found this answer helpful
Q:Photo shows round holes. Description says slotted. Which is it?
by|Dec 9, 2021
2 Answers
Answer This Question
A: Round
by|Feb 29, 2024
2 found this answer helpful
A: For the Everbilt 1-1/4 in. x 48 in. Zinc-Plated Punched Angle, the term “slotted” is used to describe the punched round holes in the angled steel.
by|May 7, 2023
2 found this answer helpful
Q:What is diameter of punched holes?
by|Mar 1, 2021
3 Answers
Answer This Question
A: The diameter of the punches holes in the 1-1/4 in. x 48 in. Zinc-Plated Punched Angle is 0.39 inches.
by|Dec 3, 2023
3 found this answer helpful
A: The punched holes measure .386" They will accomodate 3/8" fasteners,.
by|Apr 23, 2024
7 found this answer helpful
A: I currently don't have any but if I remember correctly it's 3/8'.
by|Sep 14, 2021
1 found this answer helpful
Q:Can you paint these zinc plated angle irons? Is there a special prep/paint/sealer that you would have to apply first?
by|May 26, 2020
3 Answers
Answer This Question
A: Generally, it is adiquate to wash galvanized surfaces with detergent / water solution (dish soap) prior to painting. There are primers available specifically for galvanized (zink plated) metal.
by|Apr 16, 2024
2 found this answer helpful
A: Yes you could paint right over it, no problem.
by|Mar 1, 2021
A: The punched angle can be painted after proper paint prep.
by|Dec 2, 2022
1 found this answer helpful
Q:Can I hang a swing from it that would support up to 100 lbs of weight?
by|May 20, 2019
4 Answers
Answer This Question
A: Depends on the gauge that you purchase.
by|Jul 22, 2019
A: This is not a recommended application as punched angle is not for support of human weight.
by|May 21, 2019
A: Probably not. It bends pretty easy and #100 would actually be more, due to inertia.
by|May 29, 2022
1 found this answer helpful
A: In tension, (with the load applied from end to end, along the axis) this would easily handle 100 lbs.
With the load applied perpendicular to the axis (exerting a bending force) this material could safely support 100 lbs. over only a very short span, probably less than 5 inches.
This material is only about 1/32" thick. I can't visualize exactly how you intend to support the load of your swing but it would appear that you'd need a thicker steel angle. Approximately 1/8" thick would seem more appropriate.
by|Mar 5, 2024
4 found this answer helpful
Q:What is the yield stress and tensile strength of the material?
by|Jan 18, 2019
2 Answers
Answer This Question
A: The manufacturer is unable to provide this information.
by|Jun 11, 2021
A: This is mild steel. Tensile strength would be somewhere around 50,000 psi. Given the cross sectional area of this product and allowing for the perforations, You could expect about 3000 lbs. yield strength under laboratory conditions. For a reasonable working load, considering that it would be applied via suitable bolts through individual perforations. I'd estimate about 1000 lbs. max.
This is thin, "light-duty" material. Use caution.