Questions and Answers for Eaton 1 Gang Recessed Multimedia Cable Wall Plate - White

A:  Hello, Unfortunately none of our Multimedia outlets or plates are rated for outdoor use.

A:  Mounts in a single gang box... like the box inside the wall used on all outlets and light switches. Select an "old" or "new" construction box depending on your installation.

A:  Thank you for your question. This device does not require a mounting plate.

A:  You do need a cut out to place this wall plate in but no mounting plate it needed. The finished product looks just like the photo.

A:  On the box instructions specifically says that the mounting plate is sold separately. There are applications, as in mine where I don’t need or want to install a single gang box and it would be helpful if Home Depot sold the mounting plate as described.

A:  I didn't mentioned it needed a mounting plate because it could be use without one, on my installations I see what will work better depending on the project and I make the call whether to use or not a mounting plate. They are sold in bix box stores.

A:  Thank you for your question. Unfortunately there is not a cover for the hole.

A:  No, this model does not come with a cover.

A:  No.

A:  Yes there is. Home Depot has Leviton, Preferred, solid white wall plates that are 3/8 inch larger and should cover the hole perfectly. Remove the 2 screws on the multimedia plate and replaced with the solid plate which can be painted to match the wall. Go to the electric department and ask someone who works there for help in finding it.

A:  No, there is not a cover. The only way to cover the hole will be replacing the plate. You can get a .25 cents cover to replace it.

A:  No there isn’t. If you no longer use, I would just buy a white blank plate and swap it out.

A:  No, you can't run a power cord behind the wall just like that based on codes. Just check your local electric codes to make sure you are doing the right thing.

A:  Following local building codes would be your best bet. My guess is that it's not going to be advised. Putting insufficiently sized power cords, or any electrical cord splices behind drywall would definitely be considered a fire hazard. Also, these plates are specifically marketed as 'Low Voltage/Data Cables Only'.

A:  It's considered fire hazard, insurance will not cover and inspector will no pass it. Electric Code Violation

A:  If if an extension cord, I don't see a problem

A:  Technically, it will fit, BUT it is a violation of electrical code. Only in-wall rated cabling can be used for power.

A:  Thank you for your question. Yes, a three prong plug will fit through this product.

A:  I have a extension cord, three hdmi cables and an optical cable going through mine.

A:  Yes, if you're talking about what would commonly come standard with electrical equipment (TV, monitor, computer, etc.).

A:  I was able to fit a standard 3-prong plug through the opening of this plate and still had room for a couple more, smaller cables.

A:  Yes, BUT running in-wall power that way violates electrical code. You must use in-wall rated cabling for power.

A:  Yes

A:  Thank you for your question. Unfortunately, we do not offer this product in metal.

A:  Hi ChrisM, unfortunately we do not offer the this wall plate in metal on Homedepot.com. We appreciate your business and look forward to serving you in the future. Thank you for shopping Home Depot!

A:  Use the "1 gang non-metallic work bracket" with the installation and use it as your template.

A:  No, mine didn't.

A:  Thank you for your question. This product does not come with a template.

A:  There was not a template when I purchased this wall plate, just screws. However, you will need a bracket that mounts flush to the drywall and has the thread for the plate screws to attach to. (Link below) The hole in the bracket serves as a template. http://www.homedepot.com/p/Carlon-1-Gang-Non-Metallic-Low-Voltage-Old-Work-Bracket-SC100RR/100160916?MERCH=REC-_-PIPHorizontal1_rr-_-203492457-_-100160916-_-N

A:  use the "1-gang non-metallic work bracket ($1.39). It's wide open.

A:  When I ordered, I was thinking I'd be screwing into drywall using drywall anchors. However, after seeing it up close, that wasn't going to be practical, as there wouldn't be enough meat left for the top screw after the requisite hole in the wall is cut (the picture shown is misleading). So, yes, some kind of mounting plate is needed. My solution was to cut the back half off a blue plastic 'old work' one gang outlet box (easy with common hack saw) and use that for the mounting plate. It's cheap, and works quite well.

A:  Here is a link to the plate you would need to install first. http://www.homedepot.com/p/Carlon-1-Gang-Non-Metallic-Low-Voltage-Old-Work-Bracket-SC100RR/100160916?MERCH=REC-_-PIPHorizontal1_rr-_-203492457-_-100160916-_-N