Questions and Answers for Dremel 1/8 in. Rotary Accessory Rectangle-Shaped Tungsten Carbide for Steel, Stainless Steel, Iron, Ceramics, and Hard Wood

A:  The Dremel 9901Tungsten Carbide Cutter is tested and recommended to be used with our Dremel Rotary Tools only. For further assistance, please contact us at 1-800-4-DREMEL (1-800-437-3635), Monday-Friday, 8A-5P CST.

A:  For further assistance, please contact us at 1-800-4-DREMEL (1-800-437-3635), Monday - Friday, 8A - 5P CST.

A:  This tool would work on small openings in a shower stall but might not be the best option for large projects.

A:  The Dremel 9901 Tungsten Carbide Bit will not work for cutting fiberglass wall. For further assistance, please contact us at 1-800-437-3635, Monday - Friday, 8A-5P CST.

A:  I would say yes, drill a pilot hole and then you can make a clean cut

A:  I think it would work fine but recommend that you use the lowest speed and of course hold the Dremel with both hands to maintain control.

A:  It cuts metal well so plaster should be no problem.

A:  I don’t think this bit matches the intended use. This bit is for cutting laterally. You should be able to get a different bit, perhaps for a conventional drill instead of a Dremel tool.

A:  For further assistance, please contact us at 1-800-4-DREMEL (1-800-437-3635), Monday - Friday, 8A - 5P CST.

A:  Not very good Dremel does make an attachment saw for rotary tools.

A:  this should work fine.

A:  For further assistance, please contact us at 1-800-4-DREMEL (1-800-437-3635), Monday-Friday, 8A-5P CST.

A:  Yes. It worked fine for me in cutting through steel.

A:  Steel makes very tiny slivers .quitenasty.

A:  The Dremel 9903 Tungsten Carbide Cutter is designed for shaping, smoothing and material removal. For further assistance, please contact us at 1-800-4-DREMEL (1-800-437-3635), Monday-Friday, 8A-5P CST.

A:  It might have too much power and remove too much metal. I think that a Dremel grinding wheel would be better.

A:  yes it can be used but not knowing the material you are working with you could remove to much material. Look at other bits for a Dremel tool some of the abrasive bits might be better they will remove material more slowly and you will have better control. Attached is a bit guide.

A:  Only wall tile.

A:  Yes although be careful because it can also cut the edge of the tile.

A:  The Dremel 9903 Tungsten Carbide Cutter is not recommended for removing grout. To remove grout, we suggest using our Dremel 568 Grout Removal Attachment. For further assistance, please contact us at 1-800-4-DREMEL (1-800-437-3635), Monday-Friday, 8A-5P CST.

A:  The Dremel 9903 Tungsten Carbide Cutter is about 1-1/2" in length. For further assistance, please contact us at 1-800-4-DREMEL (1-800-437-3635), Monday-Friday, 8A-5P CST.

A:  The bit is 1-1/2" long. The cutting edge from the tip is 5/8".

A:  Since this bit is 1/8 of an inch and is used in Dremel tools total length should be 1.5 to 2 inches. Most Dremel working depth is about 1 inch off the end of the locking nut. The bit needs to insert into the Dremel about 1/2 inch,

A:  About 2 inches overall. I do NOT like to use these bits on steel as tiny sharp shards stick in skin.