We've updated your selection

    Winchester   120,000 BTU 96% 2-Stage Variable Speed Multi-Positional Gas Furnace

    Set your store for local inventory & pick up options.
    • Description
      • 120,000 BTU 2-stage natural gas furnace, electronic ignitions
      • Furnace sold without installation or permitting
      • Equipment should be sized/installed by a qualified technician

      Ideal for new or replacement residential or commercial installations. The 120,000 BTU W9V Series 96% efficiency 2-stage, multi-positional, variable speed gas furnaces have a 33 in. tall cabinet and are designed for installation in up-flow, down-flow, and horizontal applications. These high efficiency furnaces are natural gas ready and convertible to propane (LP Gas) with the optional LP 347 conversion kit. Factory shipped for installation in up-flow and horizontal applications and can be easily converted for down-flow applications. Certified for Category IV venting and may be vented either through a side wall or roof applications using approved plastic as allowed by the National Fuel Gas Code. Features an electronic hot surface igniter for increased safety and efficiency, and variable speed maintenance free ECM blower that never needs lubrication, and self diagnostic control module to monitor operation. The primary heat exchanger is constructed of tubular aluminized steel and has a stainless steel secondary heat exchanger. Units are factory assembled, wired and tested to assure safe dependable and economic installation and operation. NOTE: Requires 1/2 in. input to gas valve, dedicated circuit breaker, and 120-Volt wiring with proper polarity and ground. 5 year limited parts warranty; lifetime limited heat exchanger warranty, 10 year heat exchanger warranty on commercial applications. Dimensions: 33 in. H x 24.5 in. W x 29.5 in. D. Not certified for mobile home use.

      • Natural gas ready and may be converted to LP gas with optional conversions kit
      • Multi-positional design with compact cabinet height of 33 in. for flexible installation
      • High tech tubular aluminized primary and stainless steel secondary heat exchangers
      • Built-in, high level self diagnostics with fault code displays standard on integrated control module for reliable operation
      • ECM variable speed drive for cooling SEER enhancement, improved comfort with optional airflow delay profiles, and continuous fan options for IAQ performance, low unit amp requirement for easy replacement application
      • 2 stage heating operation includes 2 stage gas valve, 2 stage inducer operation and variable speed ECM blower operation, adjustable delay timer allows 2 stage operation with a single stage thermostat
      • Equipment should be sized, selected and installed by a qualified professional to ensure proper installation, safe operation, adherence to federal, state and local codes and for valid warranty; see installation guide for more details
      • Professional installation recommended
      • Click here for more information
      • Click here for more information on Electronic Recycling Programs
    • Specifications
      Annual Fuel Utilization Efficiency (AFUE) (%) :
      Energy Consumption (kWh/year) :
      Fuel Gauge :
      Gas or Electric :
      Heat rating (BTU/hour) :
      Heating Product Type :
      Forced Air Furnace
      Heating Technology Type :
      Forced Air
      Number of Blower Speeds :
      Power/Fuel Type :
      Natural Gas
      Product Depth (in.) :
      Product Height (in.) :
      Product Weight (lb.) :
      Product Width (in.) :
      Returnable :
    • Reviews

      Ratings & Reviews

      100% of customers recommend this product
      Out of 5:
      Customer Images (2)
      • So far so good, very satisfied all around
      • March 18, 2015
      • Recommended Product

      I'll write a lengthy review for this since there are currently no others. The reviews for other models were important to me during the selection process, so hopefully this review will help someone else. Background... I live in the Mideast USA and needed a furnace for my church. We did not have enough money to pay for labor nor do we trust any contractors, so our only option was a self-install. Home Depot turned out to be one of the only places that someone like me could just go buy a furnace. Summary... So far, all is positive. Although it was a dizzying amount of work, the installation went without any problems and the furnace performs very well. More details below. Price... The price was competitive with other major brands, assuming the reliability holds out. Delivery... It came quick. We did site-to-store. It’s heavy, so wherever you have it delivered, make sure you have help to move it. Installation... None of us had ever done any HVAC work, ever. We had plenty of experience with general construction, gas lines, plumbing, etc., but no specific HVAC knowledge. Thankfully, the manual was very thorough and allowed us to complete the job. We followed it line-by-line and the furnace works great. One caveat... if you do not have extensive handyman skills, I would advise to forget any ideas of self-installation. You really need to know a lot about a lot of things, especially if you do not have previous HVAC knowledge. In our case, we also had to install all the ductwork as well. It all works exceedingly well but again, it is a significant challenge that is not for the DITY beginner. Calibration/configuration... The manual is very thorough about checking/adjusting manifold pressures, temperature rise, fan speed, etc. Even if you've never done it before, if you read carefully, you can figure it out. You'll need to buy some tools like a manometer and a thermometer. I used an inexpensive charcoal grill thermometer with a probe... very easy to slip into the duct to get a reading. Performance... It heats like a champ. Good air flow and quick heat, and very quiet. The 96% efficiency is great, as is the two-stage operation. In our case, the building is unoccupied for part of the week, so we like to turn the heat down. It's great to come in and be able to heat up things quick, then it switches to the low stage for temperature maintenance. One thing to note... this furnace produces A LOT of condensate at high stage. Be prepared for that. Technical support... Very good, I think. Hamilton (the primary dealer) actually called me to confirm that I was ordering the right size furnace, in case I was just shooting in the dark. They asked me questions about square footage, etc. A smooth move on their part, I thought. There is an odd chain of distribution from the actual manufacturer through to Home Depot. I don't know what impact that has on the consumer as far as future support, parts availability, etc. And actually, this points to the only slightly off-color thing about the furnace... the front cover has this small area that says "Place brand logo here," as if Hamilton forgot to put on the Winchester sticker. That seemed a little sloppy and made me nervous, but like I said, everything else went well. And finally... just a few things of note that spring to mind: 1) The specs make it difficult to figure out the size of the opening for the plenum and some other things, like how the air filter rack should fit. Home Depot sells a 16x25 air filter rack by Winchester, model FR 1625. That’s what you want – two of them. You might need some innovation to get them on right. 2) Hamilton told me that this unit needs a return air box on each side. Word to the wise... heed that advice. It circulates a lot of air at top CFM. 3) Hamilton kept talking about a blower motor that "ran longer than other units" and almost implied that it runs all the time. I see no behavior like that... acts like a normal furnace to me where things turn on and turn off as expected. 4) The gas manifold input is configured to take a 1/2 inch threaded fitting, like the end of a 1/2 inch threaded black iron pipe. We ran black iron all the way from the gas meter to the manifold and I would recommend the same (3/4” most of the way, then 1/2” into the furnace). The manual is not specific about this. 5) As I mentioned before, the manual is your friend. Read every word. In closing, I'll mention that we actually have a second system to install. So, we will be purchasing another identical unit in the near future without hesitation. Good luck and stay warm!

      Pros good documentation, good performance

      Video & Photo

      • DIY


      35 to 44, Male
      21 out of 21 people found this helpful
      more details...
      By: rdw357
    • Shipping & Delivery Options

      Shipping options for [zipcode] (change)

      Arrival dates and shipping costs shown above are estimates.See exact dates and costs and select your preferred shipping option during checkout.


      Express Delivery from Store is available for items currently in stock at a The Home Depot store within a delivery ZIP code. A driver from a local store will deliver the item(s).

      Outside Delivery:  Service includes delivery to area outside the house which is accessible by delivery equipment.

      Threshold Delivery: Service includes delivery across your first doorway or threshold (ie. garage, backyard, deck, first room of the home).

    This item cannot be shipped to the following state(s): AK,CA,GU,HI,PR,VI

    Find More Forced Air Furnaces TAP TO FILTER