We've updated your selection
Rheem RETE-7 - 7kW 0.21 GPM Point of Use Tankless Electric Water Heater
Set your store
for local inventory & pick up options.
- Same-day installation in most areas. Call 1-855-400-2552 by noon.
- RETE 7
- Store SKU:
The Rheem RETE-7 Point of Use Tankless Electric Water heater features a rugged brass and copper heat exchanger that is designed to withstand tough water conditions for long life. Its lightweight and compact design saves space and enables simple installation in a variety of locations. It is designed to provide hot water a single bathroom in warmer climates. Please click the "More Info" Tab and the "Specifications" to view the Rheem Brochure Guide to assist you in your purchasing decision.
- Provides a maximum of 1.37 GPM continuous flow at a 35°F temperature rise
- Designed to provide continuous hot water at a single point-of-use faucet
- Flow rate provided by a tankless electric water heater is dependent on the difference in temperature of the incoming cold water supply and the desired hot water delivery temperature
- 7kW water heater requires a 240-Volt electrical service, a dedicated 30 Amp breaker and 10-Gauge copper wiring
- Energy efficient, uses hot water only when needed
- On-unit temperature controls and LED lights indicate active elements and system operation
- Modulating control adjusts power consumption to meet the required hot water temperature and flow rate
- Rugged brass and copper heat exchanger is designed to withstand tough water conditions for long life
- Lightweight and compact design saves space and enables simple installation in a variety of locations
- Requires 240-Volt electrical connection
- Equipped with 1/2 in. water connections for easy installation
- Modulating Control adjusts power consumption to meet the required hot water / temperature flow rateHow to Choose Your Rheem EcoSense Tankless ElectricChoose your application, ie. shower, bath tub or vanity sink-faucet, kitchen sink faucet or washer. See chart below.For example: you choose a kitchen sink faucet.See application chart below and locate your flow rate. For example: your flow rate is 1.5 gpm.On the map, locate the average water temperature in your area.For example: your water temperature (in Atlanta) is 55°Use the water temperature and flow rate chart to determine the model you need.For example: 1.5 gpm flow rate + 55° = RETE 9.
- Click here for more information on Electronic Recycling Programs
- Amperage (amps) :
- Application Type :
- Point of Use
- Finish Family :
- Flow Rate @ 35 F Rise (gallons/min) :
- Flow Rate @ 45 F Rise (gallons/min) :
- Flow Rate @ 55 F Rise (gallons/min) :
- Flow Rate @ 65 F Rise (gallons/min) :
- Fuel Type :
- Indoor/Outdoor :
- Maximum Temperature (F) :
- Minimum Activation Rate (gpm) :
- Minimum Temperature (F) :
- Product Depth (in.) :
- Product Height (in.) :
- Product Weight (lb.) :
- Product Width (in.) :
- 5.375 in
- Returnable :
- Water Connection Location :
- Water Connection Size (in.) :
- Water Heater Features :
- No Additional Features
- Wattage (watts) :
Ratings & Reviews
of customers recommend this product
- Good for 1 sink if incoming water is not too cold
November 16, 2011
Verified Purchase & Recommended Product
I installed the 7kw heater to boost the water temperature at a sink in the garage, far from our main water heater. It does the job; no more waiting for the water to warm up to wash my hands (or using freezing cold water).
This heater may not be adequate if your groundwater is cold or you need a high flow rate (shower, dishwasher). Our groundwater comes in at 45˚F and this unit is not able to make it hot without help from our main water heater. But as a booster for the sink it works great. It activates at a low flow rate, so you don't need to run a lot of water to have it hot.
It is compact and fairly easy to install. It fit in the cabinet under the sink. There were, however, no instructions for the electrical connection; I was initially confused by the wiring. The unit comes with a short cable out of the bottom so you don't need to open it up to connect the wiring. The cable had three wires—black, white and bare (ground). I always thought white was neutral, but in this case it is the other hot (usually red). Since it is a straight 240V appliance, it doesn't use a neutral, just the two hots and ground. Once I figured this out, installation was straightforward.
The 7kW unit draws 29 amps, so it requires heavier wiring and a dedicated circuit; I converted a 30A circuit that was previously used for an electric dryer.
I would recommend this for a single sink if your incoming water is not too cold and you don't need high flow rates. If you need more than this, then you should consider a bigger unit.
Salt Lake City
45 to 54, Male
14 out of 14 people found this helpful
This item cannot be shipped to the following state(s): AK,GU,HI,PR,VI